Identify the command to configure the configuration-register? A.) Router# config-register 0x2102 B.) Router(config)# config-register 0x2102 C.) Router(config-reg)# 0x2102 D.) Router> config-register 0x2102
2 6156Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp
1 6022Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Route# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes
1 4018Identify the prompt displayed if in privileged exec mode? A.) Router(config)# B.) Router# C.) Router> D.) Router(priv)#
2 6531'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers
2 5559Identify the command mode necessary to enter the standard ping command? A.) Router(config)# B.) Router> C.) Router(std-ping)# D.) Router(config-if)#
1 5071Identify the command to run 'setup'? A.) Router(config)#setup B.) Router?setup C.) Router#setup D.) Router>setup
1 3774Identify the command that configures serial0 for PPP encapsulation? A.) Router(config)# encapsulation ppp B.) Router(config-if)# encapsulation serial ppp C.) Router(config-if)# encapsulation ppp D.) Router# encapsulation ppp
1 4576Identify the command to display the status of the Frame Relay virtual circuit? A.) Router# show frame-relay virtual-circuit B.) Router(config)# show frame-relay pvc C.) Router# show frame-relay pvc D.) Router# show virtual
1 3887Identify the command that disables name-to-address translation? A.) Router(config-dns)# no ip domain-lookup B.) Router(config)# no address translation C.) Router(config)# no ip domain-lookup D.) Router(config)# ip domain-lookup
1 3734What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface
1 4274Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config
2 4897Identify the following command to configure a secret password to 'cisco'? A.) Router(config)#enable password cisco secret B.) Router(config)#enable secret cisco C.) Router(config)#enable secret password cisco D.) Router(config)#set secret = cisco
1 4360Identify the effect of Ctrl-Z? A.) Exits back to privileged exec mode B.) Disconnect from the router C.) Abort the ping operation D.) Exits privileged exec mode
1 4802Given an IPX network with redundant paths, what command will configure load balancing? A.) ipx load-balance B.) ip maximum-paths 2 C.) ipx maximum-paths 2 D.) ipx load-share
1 4201
What are partial updates?
What we called 64 bit mac-address in ipv6?
What is Phase od VPN in site to site and what information you will require to configure a SITE to SITE VPN
which defined peer ip address an local subnet belong to crete? (Choose two)
In which ios version 182 people can access router through telenet?
Given the configuration example: interface ethernet0 ipx network 4a ipx access-group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network tc access-list 800 permit 3d 4a Which action result from implementing this configuration? a-Traffic from network 3d for network 4a will be forwarded out e0 b-IPX network 5c will not receive any traffic c-Traffic from network 3d, destined for network 4a, will be forwarded out e2 d-Traffic from network 3d for network 3d will be forwarded out e0
What is default size of hello packets in ospf?
What s the formula for metric of ospf?
What is meant arp and rarp?
What is default cost of serial interface in ospf?
What are the types of communication in ipv6 ?
What are the different types of password used in securing a cisco router?
What port does rip use?
What is passive topology in ccna?
Explain the benefits of vlan?