Interested to Buy Any Domain ? << Click Here >> for more details...
If i connect two routers through ethernet cable and serial
cable then which has high speed and which is better among
two?
- 10 Answers
- 14796 Views
- Compaq, Inspace, Wipro, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / gautam mishra
ethernet cable should be the best option if you want to
connect two routers directly,because serial cable has a
speed of 1.5 MBPS while ethernet cable has a speed of 10to
100 MPBS.
| Is This Answer Correct ? | 9 Yes | 0 No |
Answer / robert
connection 2 router throw a ethernet cable is faster than
the serial cable because the serial cable speed is 1.54mbs
but the ethernet cable is more than that.
| Is This Answer Correct ? | 4 Yes | 0 No |
Answer / s.m.feroz ahmed
Hi,
You cannot connect 2 Routers with ethernet anc Serial Cable
you require DCE cable which communicates between 2 Routers.
We can make out which router has high speed from the
version of IOS installed if both the routers are having
same version of IOS then the speed will be same and it the
version of IOS is greater then the previous version then
the speed will be high.Mostly people beleive Bandwidth will
increase the speed but it router which will by pass
bandwidth to whole network and WAN.
| Is This Answer Correct ? | 1 Yes | 0 No |
Define routing?
routing information
What is the default IPX Ethernet encapsulation? A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP
What is the standard ISDN term for a native ISDN modem? A.) ET B.) LE C.) TE2 D.) TE3 E.) TA
What type of switching creates variable latency through the switch? A.) Cut-Through B.) Inverted C.) Layer 4 D.) Multiplexed E.) Store and Forward
Can anybody tell me how to configure a cisco router?
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
hi shain can u send me some detail about bgp so that i can enhance my knowledge over bgp and can you also teach me about the process of suppernating. now what i am thinking that this could be last visit on that site overhere.so please mail that short of thing on my gmail id i am requesting to all of the visitor that please send theire doubt or question to my new gmail id which is jitendera.ccnainterview@gmail.com.i will try to solve it if i am capable to do it Wishing all of you for great future Jitendera kaumar sinha
How many types of ethernet?
In regards to the OSI seven-layer model, at which layer is EBCDIC and ASCII? A.) Presentation B.) Application C.) Transport D.) Session E.) Datalink F.) Network
Identify the purpose of ARP? A.) Avoiding routing loops B.) Determining a workstation's IP address C.) Sending a directed broadcast D.) Determining a workstation's MAC address
Hi, I cannot download anything on my office pc. only because of that i want online practice sites. anyway thanks for providing me website
CCNA 
