In a Dark Room one Switch Board is there.If u Pressed a
Button in Switch Board the Light will 'ON'. Write the
Possible test cases?
- 7 Answers
- 10359 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / venumaha
1)Verify the Room is in dark or not
2)Verify the darkroom should have switch board accordingly.
3)Verify the switch board, should have switch with two way
action ie On/ OFF.
4)Verify the bulb when you switch on exists in the switch
board.
5)Verify the bulb when you switch off, exists in the switch
bord.
Actual Results:
1a)The room should be dark with out having any light,
2a)The dark room should have switch board appropriately.
3a)The buld should glow when we switch on
4a)The bulb should not glow when we do switch off.
| Is This Answer Correct ? | 2 Yes | 0 No |
Answer / guest
1.Blub will glow in normal.
2.Blub will glow with low volatge.
3.Blub will glow with high volatge.
4.Blub will glow with very high volatge and burn
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / durga prasad ms
I think we can write positive and negative also
1. Switch on the light and light should glow
2. Switch off the light and it should off
3. Switch on another button light should not glow(we can do
the same with other switches also)
4. Now switch on the first button again another light
should not glow (if it is there)
| Is This Answer Correct ? | 1 Yes | 0 No |
Answer / venkat
Electricity should be there.
Bulb should be there.
Connection between bulb and switch.
Working condition of the switch.
| Is This Answer Correct ? | 1 Yes | 1 No |
Answer / ritu
1.Verify the location of Switch Board. Exp Result:- Switch
Board should be reachable.
2. Verify the Button quality. Exp Result:- Button should be
pressed after on, off.
3.Verify the functionality of button. Exp Result:- 1.Light
should be ON after ON.2. Light should be OFF after OFF.
4. Verify the button functionality for continous use. Step:-
Continuous ON OFF the button. Exp Result:- Button should
work fine.
| Is This Answer Correct ? | 0 Yes | 0 No |
Answer / sambasiva reddy,ahamed ali
1.Conditional Specification:Mentioned Dark Room.
2.Swith Board:"Press" Bulb glows.
Basis paths coverage to implement a successful glow of bulb
while switch is Pressed
1.Bulb is existed.
Pre-Requirement.
To make the test case criteria :pass/fail in a dark room
search for the switch board.
The approach u make to find is heuristic search.
Test Case Action Expected
Switch On "Press"Switch Bulb glows
| Is This Answer Correct ? | 0 Yes | 1 No |
Answer / s.ram prasad.
HI
pre_Requeste: Make Sure The Switch Board Exists.
Test Data: "Switch on The Press Button".
Test Action: 1.Test Procedure: Find the switch Board &
press the Bitton.
2.Test Description: check Whether the Light
Glows.
Test Exp Result : The Light should Glow.
S.Ramprasad. Sun_ramprasad@yahoo.com
Test Avl Result :
| Is This Answer Correct ? | 0 Yes | 1 No |
Please provide the examples for following scenarios 1.High Sevierity Low Priority 2.Low Sevierity High priority
Suppose you testing Calculator application and you got problems like 1/1=2, 2/2=1, 3/3=6, 4/4=1, 5/5=10. Now how will you describe the bug title as well as give the bug description.
Explain Automation Vs Manual Testing?
What are your greatest weaknesses?
what is Severity / Prioity ? How do assian ? What are the basic things followed?
Write a test case scenario for Web-based address book?
About the security testing, how to use to security testing in web testing, suppose u will check login page, how to change password in back end in security testing
Hi Friends, What are the steps involved in STLC
When should testing start in a project?
what is meant by Priority and Severity?
What do you understand by the terms ?Response Time?, ?Pages Per Second?, ?Transactions Per Second??
When requirement / SRS document comes to a tester then Do we prepare the test cases +ve & -ve at a time?
Automation Testing 
