Answer / guest

Answer: A

Identify the purpose of the TCP 3 step handshake? A.) Setup a un-reliable connection B.) Initialize routing tables C.) Synchronize sequence numbers between hosts D.) Connection tear down process

1 Answers  

---

What is formula of hold down time of eigrp protocol?

0 Answers  

---

I received a call from client that network is down. We have 100 or 1000 of switches and routers so how could we find the client switch and its port number? and useful commands to find this ?

8 Answers   Cubicor, HCL,

---

At what layer of the OSI reference model does FRAME-RELAY map to? A.) Session B.) Physical C.) Network D.) Presentation E.) Transport F.) Datalink

2 Answers  

---

hi shain can u send me some detail about bgp so that i can enhance my knowledge over bgp and can you also teach me about the process of suppernating. now what i am thinking that this could be last visit on that site overhere.so please mail that short of thing on my gmail id i am requesting to all of the visitor that please send theire doubt or question to my new gmail id which is jitendera.ccnainterview@gmail.com.i will try to solve it if i am capable to do it Wishing all of you for great future Jitendera kaumar sinha

0 Answers   HCL,

---

What does the IPX maximum path command do? A.) Allows you to disable the TTL on an IPX packet B.) This parameter is only used in NLSP routing C.) Sets the maximum metric that can appear in the routing table D.) Configures round robin load sharing over multiple equal metric paths (parallel paths)

1 Answers  

---

Hi Everyone, i am CCNA certified, i am searching jobs related to ccna. Although i don't have experience in networking field, i found very difficult to search job(posted my resume in all job portals). I am very much interested to work in networking field, please guide me, my mail id: nagesha12adig@gmail.com; Please let me know any company taking ccna freshers(Preferably Bangalore location). Thanks guys...

1 Answers  

---

Which type of switching reads in the entire frame before forwarding it? A.) Tabling B.) Store-and-Forward C.) Inverse ARP D.) Fast Forward E.) Cut-Through F.) Routing

1 Answers  

---

What is the default routing metric used by IGRP? A.) MTU, delay, bandwidth, reliability, and loading B.) Count to infinity C.) Bandwidth and delay D.) Hop count

2 Answers  

---

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

---

You need to come up with a TCP/IP addressing scheme for your company. Which two factors must you consider when you define the subnet mask for the network? A.) The location of DHCP servers B.) The volume of traffic on each subnet C.) The number of subnets on the network D.) The location of the default gateway E.) The number of host IDs on each subnet

1 Answers  

---

What are the different memories used in a CISCO router?

0 Answers  

---