Which command will display the encapsulation type on interface
serial 0?
A.) show interface s0
B.) show all
C.) show int s0 encap
D.) show encap s0
E.) show encap
Identify 3 characteristics of a connection oriented protocol? A.) Path determination B.) Flow control C.) Acknowledgements D.) Uses hop count as metric E.) 3 step handshake
hi friend i am stuck in the big problem.this problem is regading pix firewall. i have a cisco pix 515e firewall inmy company.now when i configure it and after rebooting it the ACT link never getup.when i apply clear config all comand the ACT link get up after oveservation i see that there is fauilover problem when i apply failover active ACT link agin get up is there any way to get my firewall in standby mode rember that there is only on firewall within my n/w i am lookig towards all of you jitendera kumar sinha
Identify the command that displays ethernet0/1 interface status? A.) show interface ethernet0/1 B.) show interface ethernet e0/1 C.) show interface ethernet0.1 D.) show ethernet0/1
How many potions of ip?
What are the different types of VPN?
'Show cdp neighbors detail' show the following 3 pieces of information? A.) Hardware platform B.) Software version C.) Same as 'show version' command D.) Up to 1 address for each protocol E.) Non-direct connected routers
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
You are a network administrator and have been assigned the IP address of 201.222.5.0. You need to have 20 subnets with 5 hosts per subnet. What subnet mask will you use? A. 255.255.255.248 B. 255.255.255.128 C. 255.255.255.192 D. 255.255.255.240
The Cisco Discovery Protocol (CDP) periodically sends out a multicast packet (at layer 2). Which command will alter the default interval of 60 seconds? A.) cdp hold 111 B.) cdp wait 111 C.) cdp interval 111 D.) cdp 111 E.) cdp timer 111
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
Repeaters work at which layer of the OSI model? A.) Network B.) Session C.) Transport D.) Physical
2500 Value in which type of access list?