1. Categories >> Certifications >> Cisco Certifications >> CCNA
  2. Suggest New Category

Which three of the following are true statements about

connection-oriented

sessions?

A.) The segments delivered are acknowledged back to the
sender upon

their reception

B.) Any segments not acknowledged are retransmitted by the
receiver

C.) A manageable data flow is maintained in order to avoid
congestion,

overloading and loss of any data

D.) Segments are sequenced back into their proper order upon
arrival at

their destination

Question Posted / guest

Answers were Sorted based on User's Feedback



Which three of the following are true statements about connection-oriented sessions? A.) Th..

Answer / guest

Answer: A C D

Is This Answer Correct ?    5 Yes 1 No

Which three of the following are true statements about connection-oriented sessions? A.) Th..

Answer / girish

A B D

Is This Answer Correct ?    1 Yes 1 No

Which three of the following are true statements about connection-oriented sessions? A.) Th..

Answer / ananth

all four are correct answers

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

What are the two primary operating modes for frame switching? A. Full Duplex B. Half-Duplex C. CSMA/CD D. Cut-through E. Fragmentation F. Store and Forward G. User mode H. Privileged mode

1 Answers  

Which of the following is a valid extended IP access-list? A.) router(config)# access-list 101 permit tcp host 172.16.30.0 any eq 21 log B.) router# access-list 101 permit tcp host 172.16.30.0 any eq 21 log C.) router(config)# access-list 101 permit any any 172.16.30.0 D.) router(config)# access-list 101 permit ip host 172.16.30.0 any eq 21 log

2 Answers  

Why is network segmentation a good idea when managing a large network?

0 Answers  

Can you explain CHAP?

1 Answers   CCIE,

Identify the command to disable CDP on an interface? A.) Router(config-if)# no cdp enable B.) Router(config-if)# no cdp run C.) Router# no cdp enable D.) Router(config-if)# no cdp

1 Answers  




What is network?

0 Answers  

Can you explain PPP link process step by step?

0 Answers   CCIE, Sawes,

What is the size of ipv6?

0 Answers  

The maximum distance on a 10BaseT network from the hub to a workstation is which of the following? A.) 500 meters B.) 1000 meters C.) 100 meters D.) 1500 meters

2 Answers  

What is the Function of Layer3 Switch?

1 Answers  

Identify the hardware component that stores the backup configuration? A.) RAM B.) NVRAM C.) Flash D.) ROM

1 Answers  

HI friends mine one of the friends have ask a good question i also donot know the answer so i am putting here Please poet the answer no matter it is wright or wrong put yours view here The question is like that when we are going to configure ospf then there are three way 1st way router ospf 10 netwrok 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 the 2nd way is like that router ospf 10 netwrok 192.168.0.0 0.0.255.255 area 0 but he inrodused the thrird way like router ospf 10 netwrok 192.168.00000001.0 < ?.?.?.?>area 0 router ospf 10 netwrok 192.168.00000010 <?.?.?.?>area 0 now problem is that what should i put the mask in this way so i puted ? sign Please solve this problem i think this is good one plz donot see for answer please contribute any thing i am reqesting Than you Jitendera kuamr sinha

5 Answers  

For more CCNA Interview Questions Click Here
Categories