Identify the 2 commands that save the running-config to a TFTP
server?
A.) write running tftp
B.) copy running network
C.) copy running tftp
D.) write network
- 3 Answers
- 4160 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
can anybody send sample question on CCNA Exam.pls send to my email ca6thi@gmail.com
What is true about Link-State protocols? A.) They maintain a more complex table than distant vector protocols B.) They maintain a less complex table than distant vector protocols C.) They use routing ports D.) The maintain backup copies of the IOS
What key do you use to view the last command? A.) Ctrl+X B.) Ctrl+Z C.) Ctrl+E D.) Ctrl+P
In Cisco IOS software which command displays the backup configuration? A. show flahh B. show version C. show tftp-config D. show backup-config E. show startup-config
Which IP packet field will prevent endless loops? type-of-service identificationf lags time-to-live header checksum
hi friends i have some problem regarding technical round ahr round plz tell me what should the right answer technical questions 1 what is brouter 2 what is the menaing of 10 base2, 10 base 5 and 10baset 3 what is diffrence between bit rate and baud rate. and this question was tooooooooooo much difficult to me that hr said to me that rank me after the taking the all short of interview
What do you use the Aux port for? A.) Console B.) Terminal editing C.) Modem D.) Backup logging
Dear Mr.Shahin thank you very much for your advise i realy thanks full to you. Best of luck
In port based access-list which command u give instead of ip?
In the setup dialog, what do the square brackets indicate? A. current or default spores B. hard coded values that cannot be modified C. values entered by the administrator but not saved D. values that must be written to PAVRAM before becoming enabled
Most routing protocols recognize that it is never useful to send information about a route back out the direction from which the original packet came. This is an example of which routing technology? A.) Split Horizon B.) LMI C.) Triggered Updates D.) Poison Reverse E.) SYN, ACK F.) DLCI
take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible
CCNA 
