As system administrator, you type "debug ipx sap" and

receive the following lines as part of the IOS response:

type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops

type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops

What does "0x4" signify?

A. That is a Get Nearest Server response.

B. That it is a General query.

C. That it is a General response.

D. That it is a Get Nearest Server request.




Answers were Sorted based on User's Feedback



Answer / guest

Answer: A

Is This Answer Correct ?    10 Yes 0 No

Answer / laksamba indra bahadur

A. That is a Get Nearest Server response.

Is This Answer Correct ?    0 Yes 0 No

Post New Answer




More CCNA Interview Questions

Identify 3 characteristics of switches? A.) Increase available bandwidth B.) Decrease broadcast traffic C.) Support full duplex in a multipoint topology D.) Make fowarding decision using MAC address E.) Create collision domains

1 Answers  


For IPX, what is the DEFAULT Cisco Encapsulation on an Ethernet interface? A.) novell-ether B.) gns C.) snap D.) arpa E.) sap F.) dix

1 Answers  


Identify the definition of demarcation? A.) Date in which the WAN service contract expires B.) Cabling which extends from the WAN service provider to the customer C.) Division of responsibility, where the CPE ends and the local loop begins D.) Equipment which is located at the customer premises

1 Answers  


Which command will give the following output: Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int * 0 CTY - - - - - 0 0 0/0 - 1 AUX 9600/9600 - - - - - 0 0 0/0 - * 2 VTY - - - - - 2 0 0/0 - 3 VTY - - - - - 0 0 0/0 - 4 VTY - - - - - 0 0 0/0 - 5 VTY - - - - - 0 0 0/0 - 6 VTY - - - - - 0 0 0/0 -

1 Answers  


Identify the 2 commands that display the clock rate configured on the serial0 interface? A.) show serial0 B.) show interface serial0 C.) Show clock rate serial 0 D.) show controllers serial 0 E.) show running-config

1 Answers  


What does the "IPX maximum-paths 2" command accomplish? A. It enables load sharing on 2 paths if the paths are equal metric paths. B. It sets up routing to go to network 2. C. It is the default for Cisco IPX load sharing. D. It enables load sharing on 2 paths if the paths are unequal metric paths.

3 Answers  


How the STP determinw that which Port should be Root Port, which port should be Designeted Port , Blocking Port and Forwarding Port in Layer 2 STP topology........ Hi friends Thanks for posting the answer of above given questions i agree with all of you that BPDU is the Protocol that are used to determine this is clear to me.. But I want to Know the Process like Why it Blocked the port Fa0/1 Insted of Fa0/2 waiting for Answer Posting .... Thanks in Advance

5 Answers  


In STP the Root Bridge Sends the BPDU in Every 2 Sec,In BPDU What kind of Information is i.e. What kind of information BPDU Contains?

3 Answers  


Which of the following protocols are used for logical network addressing? A.) IP B.) TCP C.) ARP D.) ICMP E.) RARP F.) BootP

1 Answers  


What IP command would you use to test the entire IP stack? A.) Stack-test B.) Arp C.) Telnet D.) Ping E.) Trace

2 Answers  


What will transport layer do when data coming from session layer. They asked about intial operation(3 - way handshake)

1 Answers   HCL,


When you enter router passwords during the setup dialog what is the difference between enable and the enable secret passwords? A. The enable password is encrypted B. The enable secret password uses IPSec password authentication C. The enable secret password cannot be seen as clear text when viewing the configuration D. The enable secret password acts as a backup in case the enable password is compromised

8 Answers   Wipro,




Categories