Answer / s.m.feroz ahmed

Hi,

You are requested to contact any of the "Prometric Center"
present in your location nearby and can book a slot for
Certification and can obtain certification by scoring and
the minimum score required to obtain certification is 80%
out of 100% percent.

WHY DO WE USE the command interface Vlan 1 ip adress x.x.x.x sub mask what does it do .. what does it create.. i know when we create it we can remotely telnet inti a router=switch. but what is the diff bwt vlan and intface vlan. ... vlan 1 bieng a native vlan remains there eve if i dont gv switch an ip address .. lease suggest.

1 Answers   Wipro,

---

Which range of possible numbers do standard ipx access lists have? A. 100 199 B. 600 699 C. 800 899 D. 1000-1099

1 Answers  

---

How does a switch use store and forward? A.) By using a Class I repeater in a collision domain B.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface C.) By using broadcast addresses as source addresses D.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets

1 Answers  

---

Which OSI Reference Layer is concerned with path determination? A.) Datalink B.) Physical C.) Network D.) Transport E.) Session

2 Answers  

---

what are the different symmetric algorithms?

0 Answers   CCIE,

---

---

Which is true regarding store-and-forward switching method? A.) Latency varies depending on frame-length B.) Latency is constant C.) It is default for all Cisco switches D.) It only reads the destination hardware address before forwarding the frame

1 Answers  

---

What is the standard ISDN term for a native ISDN modem? A.) ET B.) LE C.) TE2 D.) TE3 E.) TA

1 Answers  

---

You need to come up with a TCP/IP addressing scheme for your company. How many network IDs must you allow for when you define the subnet mask for the network? A.) One for each WAN link B.) One for each router interface C.) One for each NIC installed in each client D.) One for each subnet with hosts E.) One for each host ID

1 Answers  

---

What is bgp?

0 Answers  

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

3 router configured with RIP & Ripv2 rotuer 1- connected with router 2 having sr ip 10.0.1.2 routing : ripv2 router 2: connected with router 1 and router 3 having sr 0 ip 10.0.1.3 & sr 1 ip 11.0.1.2 routing :rip & ripv2 router 3: connected with router 2 having sr ip 11.0.1.3 routing: rip is there communication possible btween these networks ? if yes how

2 Answers  

---

What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface

1 Answers  

---