CHEMICAL ENERGY BALANCE - EXAMPLE 11.1 : Please match the term A - E with the stated definition i - v. Terms : A. Yield. B. Selectivity. C. Relative saturation. D. Molal saturation. E. Absolute saturation. Definitions : i. (moles of desired product formed) / (moles that would have been formed if there were no side reactions and the limiting reactant has reacted completely); ii. (moles of desired product formed) / (moles of undesired product formed); iii. (relative humidity 40 % means partial pressure of water vapour equals 4 / 10 of the vapour pressure of water at the system temperature); iv. (moles of vapour) / (moles of vapour dry gas); v. (mass of vapour) / (mass of dry gas).

CHEMICAL ENERGY BALANCE - EXAMPLE 11.2 : Calculate the cooling duty, H required to condense and cool acetone from 100 degree Celsius to 25 degree Celsius at atmospheric pressure. The heat of vaporization for acetone at its normal boiling point is 30.2 kJ / mol. The boiling point of acetone at atmospheric pressure is 56 degree Celsius. The flowrate of acetone through the condenser is 100 mol / s = N. Value of sensible heat needed to increase the temperature of acetone in liquid form from 25 to 56 degree Celsius is 4.06 kJ / mol. Value of sensible heat needed to increase the temperature of acetone in vapor form from 56 to 100 degree Celsius is 3.82 kJ / mol. Unit of H is kJ / s.

CHEMICAL ENERGY BALANCE - EXAMPLE 11.3 : For liquid benzene, the CP constants are : a = 129440, b = - 169.5, c = 0.64781. Reference temperature is 298 K. The temperature of benzene is 60 degree Celsius. Calculate the enthalpy of benzene by using the formula H = a (DT) + (b/2) (T^2 - TREF^2) + (c/3) (T^3 - TREF^3) where ^ is power, DT is temperature difference with TREF = 298 K. H is in J / kmol. DT = T - TREF.

CHEMICAL ENERGY BALANCE - EXAMPLE 11.4 : Calculate the bubble temperature T at P = 85-kPa for a binary liquid with x(1) = 0.4. The liquid solution is ideal. The saturation pressures are Psat(1) = exp [ 14.3 - 2945 / (T + 224) ], Psat(2) = exp [ 14.2 - 2943 / (T + 209) ] where T is in degree Celsius. Please take note that x(1) + x(2) = 1. Please take note that y(1) + y(2) = 1, y(1) = [ x(1) * Psat(1) ] / P, y(2) = [ x(2) * Psat(2) ] / P, * is multiplication. P is in kPa.

CHEMICAL ENERGY BALANCE - EXAMPLE 11.5 : According to Margules Equation, P = x(1) p(1) g(1) + x(2) p(2) g(2) for a two-component mixture where P is bubble pressure, x is mole fraction, p is saturation pressure, g is constant given by ln g(1) = x(2) A x(2). Find the value of A as a constant when P = 1.08 bar, p(1) = 0.82 bar, p(2) = 1.93 bar in a 50 : 50 mole fraction mixture. Estimate the pressure required to completely liquefy the 30 : 70 mixture using the same equation, by proving P = 1.39 bar. Take note that ln g(2) = x(1) A x(1), ln g(1) = x(2) A x(2).

ENGINEERING MATERIAL - EXAMPLE 12.2 : At 150 degree Celsius, a mixture of 40 wt % Sn and 60 wt % Pb present, forming phases of alpha and beta. Chemical composition of Sn at each phase : CO (overall) : 40 %, CA (alpha) : 11 %, CB (beta) : 99 %. (a) State 2 reasons for the existences of alpha and beta phases for the mixture of Sn - Pb at 150 degree Celsius. (b) By using Lever Rule, calculate the weight fraction of each phase for alpha, WA = Q / (P + Q) and beta, WB = P / (P + Q) where Q = CB - CO and P = CO - CA.

REACTION ENGINEERING - EXAMPLE 13.1 : In a furnace, 2 chemical reactions are happening - 1 mole of solid carbon reacts with 1 mole of oxygen gas to generate 1 mole of carbon dioxide gas; 1 mole of solid carbon reacts with 0.5 mole of oxygen gas to generate 1 mole of carbon monoxide gas. In a given process, 100 kmol of carbon is burned in a furnace. (a) Calculate the theoretical oxygen gas needed by assuming that all the carbon is burned completely to carbon dioxide gas. (b) Calculate the theoretical air needed by assuming that all the carbon is burned completely to carbon dioxide gas and there is only 21 % of oxygen gas. (c) Determine the amount of air required (in kmol) if 50 % excess oxygen gas must be satisfied for (a) and (b). (d) It has latter been found that 20 % of the carbon undergoes incomplete combustion resulting to carbon monoxide gas production. The rest of the carbon undergoes complete combustion. Calculate the total oxygen gas required stoichiometrically based on the actual process.

ENGINEERING MECHANIC - EXAMPLE 15.3 : A biochemical trolley of mass 15 kg is towing a trailer of mass 5 kg along a straight horizontal pathway. The trailer and the trolley are connected by a light inextensible tow-bar. The engine of the trolley exerts a driving force of magnitude 100 N. The trailer and the trolley experience resistances of magnitude 10 N and 30 N respectively. (a) Form 2 equations with unknowns T and a, that represents the equilibrium for the 2 systems of the trolley and trailer. (b) Solve the simultaneous equations from the 2 equations that are obtained in part (a) of this question. T is the tension of the tow-bar and a is the acceleration.

ELECTRICAL TECHNOLOGY - EXAMPLE 16.2 : In a selection of suitable heating equipment for drying of crystals of biochemical, the one of the lowest current consumption will be chosen for safety consideration. Selection is available : (A) 120 V microwave oven 1800 W. (B) 240 V conventional oven 11000 W. Which one should be chosen and why?

ELECTRICAL TECHNOLOGY - EXAMPLE 16.3 : In the design of a solar power system steps of calculations below are followed : (a) The power output of the inverter of the solar panel is 100 watts. What is the power input, Pin to the inverter when the efficiency of the inverter is 50 %? (b) If the rated power of the inverter is 300 watts, how many inverter is needed for the solar panel? (c) Charge controller of V = 12 volts is used to supply power to the inverter. What is the input current I to the inverter? (d) If the charge controller capacity is 10 A, how many charge controllers are needed? (e) If a biochemical mixer consumes 100 watts, running for 2 hours per day, what is the energy consumption in kilowatt hour per day? (f) What is the input energy needed when the efficiency of the inverter is 50 %? (g) If your area receives 2.88 hours of full sunlight per day, how much energy, in kilowatt hour can be produced per day when one solar panel can produce 20 watts of power? (h) If you know that you have to produce total energy as the answer for (f), how many solar panels are needed? (i) Each V = 12 V battery has 5 ampere hours. If the total energy needed is in answer (f), then how many batteries are needed to run the biochemical mixer if without sunlight for 3 days?

at which depth the construction of tunnel is economical from cost and engineering aspect.

COMPUTER PROGRAMMING FOR ENGINEERS - EXAMPLE 17.3 : (a) The byte is the basic building block of computer data used in chemical engineering process simulation where 16 bits make a word, 4 bits make a nibble, 32 bits make a quad word and 8 bits make a byte. Then how many nibbles are there in a megabytes? (b) In computer data items, let : 1 bit - counts from 0 to 1, 8 bits - counts from 0 to 255, 16 bits - counts from 0 to A. What is the value of A? (c) In a binary system of 4 bits, if 1100 = 12, 1101 = 13, 1110 = 14, 1111 = 15, B = 16, then guess the value of B. (d) By using any form of tools, find the exact value of 2 power 64 or 2^64.

PROCESS DESIGN - EXAMPLE 21.1 : According to rules of thumb in chemical process design, consider the use of an expander for reducing the pressure of a gas when more than 20 horsepowers can be recovered. The theoretical adiabatic horsepower (THp) for expanding a gas could be estimated from the equation : THp = Q [ Ti / (8130a) ] [ 1 - (Po / Pi) ^ a ] where 3 ^ 3 is 3 power 3 or 27, Q is volumetric flowrate in standard cubic feet per minute, Ti is inlet temperature in degree Rankine, a = (k - 1) / k where k = Cp / Cv, Po and Pi are reference and systemic pressures respectively. (a) Assume Cp / Cv = 1.4, Po = 14.7 psia, (temperature in degree Rankine) = [ (temperature in degree Celsius) + 273.15 ] (9 / 5), nitrogen gas at Pi = 90 psia and 25 degree Celsius flowing at Q = 230 standard cubic feet per minute is to be vented to the atmosphere. According to rules of thumb, should an expander or a valve be used? (b) Find the outlet temperature To by using the equation To = Ti (Po / Pi) ^ a.

PROCESS DESIGN - EXAMPLE 21.3 : According to a heuristic of chemical engineering plant design, assume a pressure difference dP = 4 psi for each 10-ft rise in elevation. A pump is needed to pump liquid from a storage tank at a lower elevation to a heating tank at a higher elevation with the elevation difference of 60 ft. (a) Find the pressure loss due to such elevation. (b) If the required minimum inlet pressure to the heating tank is 9 psi, with 1 control valve is installed between pump and heating tank, what is the dP minimum required for the control valve and the entrance to the heating tank when the heuristic mentions that at least 10 psi is required for the control valve? (c) The pressure at the inlet of the pump is 8 psi and the flowrate of the liquid produces pressure head of 50 psi. What is the total pressure produced by the pump? (d) Assume a pipeline dP of 2 psi / 100 ft for liquid flow in a pipe according to heuristic, what is the approximate maximum length of the pipe in ft that can be installed between the pump and the heating tank?

ENVIRONMENTAL ENGINEERING - QUESTION 22.2 : Biochemical Oxygen Demand (BOD) could be calculated using the formula BOD = (DOi - DOf) (Vb / Vs) where Vb = Volume of bottle in ml, Vs = Volume of sample in ml, DOi = Initial dissolved oxygen in mg / L, DOf = Final dissolved oxygen in mg / L. (a) By using a bottle of Vb = 300 ml with sample Vs = 30 ml, find the BOD if DOi = 8.8 mg / L and DOf = 5.9 mg / L. (b) By using a bottle Vb = 600 mL with sample Vs = 100 mL, find the BOD if DOi = 8.8 mg / L and DOf = 4.2 mg / L. (c) Find the average BOD = [ Answer of (a) + Answer of (b) ] / 2. (d) If the BOD-5 test for (a) - (c) is run on a secondary effluent using a nitrification inhibitor, find the nitrogenous BOD (NBOD) = TBOD - CBOD. Let TBOD = 45 mg / L and CBOD = Answer of (c).