Interested to Buy Any Domain ? << Click Here >> for more details...
how many default route can be configure on a router
- 3 Answers
- 6539 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / krishan kumat rai
we can create 16 default route in cisco router but by default
4 route are enable
| Is This Answer Correct ? | 5 Yes | 2 No |
The Sweet 16 is come in the scenario when we configure
Routing protocol.
It will be a matter of concern when we are going for load
balancing process.
So dude, will u explain hw can we config on;y 16 route... I
am gonna paste of my router config where 30 default routes
configured so far...
ip route 0.0.0.0 0.0.0.0 1.1.1.1
ip route 0.0.0.0 0.0.0.0 1.1.1.2
ip route 0.0.0.0 0.0.0.0 1.1.1.3
ip route 0.0.0.0 0.0.0.0 1.1.1.4
ip route 0.0.0.0 0.0.0.0 1.1.1.5
ip route 0.0.0.0 0.0.0.0 1.1.1.6
ip route 0.0.0.0 0.0.0.0 1.1.1.7
ip route 0.0.0.0 0.0.0.0 1.1.1.8
ip route 0.0.0.0 0.0.0.0 1.1.1.9
ip route 0.0.0.0 0.0.0.0 1.1.1.10
ip route 0.0.0.0 0.0.0.0 1.1.1.11
ip route 0.0.0.0 0.0.0.0 1.1.1.12
ip route 0.0.0.0 0.0.0.0 1.1.1.13
ip route 0.0.0.0 0.0.0.0 1.1.1.14
ip route 0.0.0.0 0.0.0.0 1.1.1.15
ip route 0.0.0.0 0.0.0.0 1.1.1.16
ip route 0.0.0.0 0.0.0.0 1.1.1.17
ip route 0.0.0.0 0.0.0.0 1.1.1.18
ip route 0.0.0.0 0.0.0.0 1.1.1.19
ip route 0.0.0.0 0.0.0.0 1.1.1.20
ip route 0.0.0.0 0.0.0.0 1.1.1.21
ip route 0.0.0.0 0.0.0.0 1.1.1.22
ip route 0.0.0.0 0.0.0.0 1.1.1.23
ip route 0.0.0.0 0.0.0.0 1.1.1.24
ip route 0.0.0.0 0.0.0.0 1.1.1.25
ip route 0.0.0.0 0.0.0.0 1.1.1.26
ip route 0.0.0.0 0.0.0.0 1.1.1.27
ip route 0.0.0.0 0.0.0.0 1.1.1.28
ip route 0.0.0.0 0.0.0.0 1.1.1.29
ip route 0.0.0.0 0.0.0.0 1.1.1.30
| Is This Answer Correct ? | 1 Yes | 1 No |
Answer / nepal
Assume you all next hops available in Routing Information
Base (RIB), then when you do "sh ip route", you will only
see default route pointing to 16 next hops (next hops will
be in ascending order, if more than 16 static default
configured)
| Is This Answer Correct ? | 0 Yes | 0 No |
Traffic Shaping does which one of the following? A. Eliminates bottlenecks by throttling back traffic volume at the source or outbound end B. Reduces the frame size so bandwidth is better utilized C. It increases source traffic to a configured bit rate D. Allows you to control hubs and repeaters
When doing an RFP (Request for Purchase) for a customer, at what step do you reiterate your solution and the customer requirements? A. Design Requirements B. Design Solution C. Summary D. Appendices
When is the route to a node determined in an SRB (Source Route Bridging) Token Ring network? A. Before any data is transmitted B. After the data is transmitted C. During the transmission of data D. After the first frame is transmitted
What layer of the OSI reference model does TCP reside in? A. Session B. Transport C. Network D. Data-Link
Which of the following does not specify an application requirement that affects your network design? A. The number of users B. The peak hours that the applications are used C. The types of applications used D. Security risks
What type of address is analyzed by a Layer 2 switch? A. network address B. MAC and network address C. Protocol type, MAC, and network address D. MAC address
When are SNMP traps sent? A. When the SNMP manager wants to perform remote configuration on a networking device B. When an SNMP agent wants to inform the SNMP manager about a change of state on the networking device C. When the SNMP manager wants to access large chunks of data D. When the NMS wants to share trap information
What is the first step in diagramming packet flow for the terminals within a network? A. Identify the end user nodes of all the terminals B. Figure out the speed of all the servers C. Find out where all the routers are located D. Find out where all the switched are located
What are two differences between 10BaseT and 100BaseT? A. Speed B. Frame format C. Addressing D. Network diameter
What PPP frame initiates the network layer protocols to be used during a connection?
When would you suggest static routes to your customers? A. When scalability is important B. When bandwidth is limited C. When the network will be changing frequently D. Always suggest static routes
A device has 2 synchronous ports, 16 asynchronous ports, and one ethernet port. What is this device most likely to be? A. CSU/DSU B. Access Server C. Multiplexer D. ISDN Terminal Adapter
CCNA 
