What does the show protocol display?

0 Answers  

---

In regards to the ISDN BRI standard, which channel is used for control? A.) B B.) D C.) E D.) I E.) Q

2 Answers  

---

What would be the proper wildcard mask to permit all odd numbered hosts on the 10.48.0.0/12 network? access-list 1 permit 10.48.0.0 0.15.255.255 access-list 1 permit 10.48.0.1 0.15.255.254 access-list 1 permit 10.48.0.0 0.15.255.1 access-list 1 permit 10.48.0.0 0.0.0.254 access-list 1 permit 10.48.0.0 0.0.0.255

5 Answers  

---

hi shain can u send me some detail about bgp so that i can enhance my knowledge over bgp and can you also teach me about the process of suppernating. now what i am thinking that this could be last visit on that site overhere.so please mail that short of thing on my gmail id i am requesting to all of the visitor that please send theire doubt or question to my new gmail id which is jitendera.ccnainterview@gmail.com.i will try to solve it if i am capable to do it Wishing all of you for great future Jitendera kaumar sinha

0 Answers   HCL,

---

bWhich form of PPP error detection on Cisco routers monitors data dropped on a link? A. Quality B. Magic Number C. Error Monitor D. Droplink

1 Answers  

---

A default route is analogous to a _________. A. default gateway B. static route C. dynamic route D. one-way route

1 Answers  

---

what is full form of rst,smtps & http?

2 Answers   HCL,

---

Identify the 2 commands that will display the status and information about interface E0 only? A.) show interface ethernet E0 B.) show interface E0 C.) show E0 D.) show int E0 E.) show interface

1 Answers  

---

Identify 3 features of IGRP? A.) Composite metric B.) New horizon C.) Flash updates D.) 60 periodic updates E.) Poison reverse

1 Answers  

---

Which command we use for ping in ipv6?

0 Answers  

---

What command do you enter at the keyboard to begin a user mode session? A.) Type 'CTRL-P' B.) Type 'login' C.) Just press . D.) Type 'enable' E.) Press 'Shift + Ctrl + 6' at the same time.

1 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

1 Answers  

---