In port based access-list which command u give instead of ip?
No Answer is Posted For this Question
Be the First to Post Answer
What is the difference between static ip addressing and dynamic ip addressing?
take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible
There are 2 types of PPP authentication supported by the Cisco IOS. What are they? A.) PAP B.) PREDICTOR C.) MD5 D.) CHAP E.) STACKER F.) MSCHAP
Identify the command that displays ethernet0/1 interface status? A.) show interface ethernet0/1 B.) show interface ethernet e0/1 C.) show interface ethernet0.1 D.) show ethernet0/1
What is the purpose of the DLCI? A.) Identifies the remote routers B.) Contained with a 802.2 frame for routing purposes C.) Used with PPP during authentication D.) Identifies the PVC in a Frame Relay network
Identify the 3 key features of the Cisco Discovery Protocol? A.) Off by default B.) Will allow for the discovery of layer 3 addresses on neighbor routers C.) Verifies connectivity D.) Open standard E.) Does not require any layer 3 protocols to be configured
What's the default CDP holdtime in seconds for Cisco routers? A.) 30 seconds B.) 180 seconds C.) 90 seconds D.) 60 seconds
Identify 3 characteristics of IP RIP? A.) Distance vector B.) Administrative distance is 120 C.) Periodic updates every 60 seconds D.) Uses a composite metric E.) Can load balance
Which layer is responsible for putting 1s and 0s into a logical group? A.) Session B.) Application C.) Transport D.) Data Link E.) Physical F.) Network
How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain
Identify the purpose of ICMP? A.) Avoiding routing loops B.) Send error and control messages C.) Transporting routing updates D.) Collision detection
8. When is Frame Tagging used? A. When you install repeaters in your network B. When you install bridges in your network C. When you install routers in your network D. When you use Switches configured with multiple VLANS