What will be the prefix length of 224 in vlsm?


No Answer is Posted For this Question
Be the First to Post Answer

Post New Answer



More CCNA Interview Questions

What is an example of a valid MAC address? A. 192.201.63.251 B. 19-22-01-63-25 C. 0000.1234.FEGA D. 00.00.12.34.FE.AA

14 Answers   Aricent,


Inverse ARP serves what purpose? A.) Method for a local router to introduce itself to the remote end of the connection B.) Broadcast a routing table update C.) Identify MAC addresses if the IP address is known D.) Sent every 10 seconds used to verify the Frame Switch is still active

1 Answers  


Given the global configuration command 'banner motd #7 Hello #', what do the '#' symbols represent? A.) Escape sequence to exit the menu. B.) Nothing, just part of the banner. C.) Tic Tac Toe Macro. D.) Delimiting Character E.) Message border character. F.) Number of times message to be displayed.

1 Answers  


What is CIDR?

6 Answers   Wipro,


What is the maximum hop count for Link-State protocols? A.) 15 B.) there is no hop count limit C.) 256 D.) 16

2 Answers  






Identify the default IPX serial encapsulation? A.) Novell-Ether B.) SDLC C.) SNAP D.) HDLC

1 Answers  


srry for inconvnce ..here is complete qs...ignore the previous 1 3 router configured with RIP & Ripv2 rotuer 1- connected with router 2 having sr ip 10.0.1.2 routing : ripv2 E0:192.168.1.10 router 2: connected with router 1 and router 3 having sr 0 ip 10.0.1.3 & sr 1 ip 11.0.1.2 routing :rip & ripv2 E0=192.168.10.2 router 3: connected with router 2 having sr ip 11.0.1.3 routing: rip E0=172.16.10.2 is there communication possible?

5 Answers   Cisco,


Identify the OSI layer responsible for end-to-end connections? A.) Network B.) Transport C.) Session D.) Data link E.) TCP

4 Answers  


Explain how many collision domains are in switch?

0 Answers  


hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  


What IP command would you use to test the entire IP stack? A.) Stack-test B.) Arp C.) Telnet D.) Ping E.) Trace

2 Answers  


Hi all of you, Actually this is interview qe? but i did,t do explain it completely so please give reply recently and completly Ans, what is sub-interface and inter-vlan ? And How to implement it on cisco router & switches and also which series router switches supported please write..........

2 Answers   Cisco,


Categories