Repeaters work at which layer of the OSI model? A.) Network B.) Session C.) Transport D.) Physical

6 Answers   Wipro,

---

An optional parameter on an IPX access is the 'LOG' parameter. This records access-list violations when a packet matches. What else does the 'LOG' option do? A.) Records the number of times that a packet matches the list. B.) Return a message to user who is denied access the by list. C.) Notifies an SNMP Agent. D.) Saves the log to NVRAM. E.) Send an SNMP Trap.

1 Answers  

---

Identify 1 characteristic of RARP? A.) MAC to IP address translation B.) Connectionless delivery of packets C.) Can be used to initiate remote O/S load sequence D.) Generates error and control messages

5 Answers  

---

if i am using active directory,i have router also.then how i configure router,means which address will be default gatway in active directory & roter how to give ip address details in router.

1 Answers   IBM,

---

Mention what is dhcp?

0 Answers  

---

The two sublayers of the IEEE Data Link Layer are which of the following? A.) Link and Logical Control B.) Data Link and LLC C.) Logical Link Control and Media Access Control D.) Data Link and MAC

2 Answers  

---

In IOS boot sequence if the flash is erased, and there is no access to TFTP server, and we can't load the partial IOS from ROM. Is there any possiblity that we can still boot the router/switch from external PC in which the IOS is installed?

6 Answers  

---

Explain the difference between tracert and traceroute?

0 Answers  

---

Which addresses are valid host addresses? A. 201.222.5.17 B. 201.222.5.18 C. 201.222.5.16 D. 201.222.5.19 E. 201.222.5.31

2 Answers   VGH,

---

Which of the follwing are true of standard half-duplex Ethernet circuitry? A. It is alternate one-way communication B. The receive (RX) is wired directly to the transmit (TX) of the remote station C. The transmit (TX) is wired directly to the receive (RX) of the remote station D. Collisions are not possible E. Both stations can transmit simultaneously

2 Answers  

---

Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

---

Identify 3 IP applications? A.) AURP B.) ARP C.) Telnet D.) SMTP E.) DNS F.) RARP

2 Answers  

---