Which command sets IGRP as the routing protocol for autonomous system 100? A. Router(config)#igrp 100 B. Router(config)#network 100 C. Router(config)#router igrp 100 D. Router(config)#enable igrp 100

1 Answers  

---

Which OSI Reference Layer is concerned with logical addressing? A.) Network B.) Transport C.) Datalink D.) Physical E.) Session

1 Answers  

---

R1#sh ip nat translations Pro Inside global Inside local Outside local Outside global icmp 15.1.1.1:11 10.1.1.1:11 30.1.1.1:11 30.1.1.1:11 icmp 15.1.1.1:12 10.1.1.1:12 20.1.1.1:12 20.1.1.1:12 icmp 15.1.1.1:13 10.1.1.1:13 21.1.1.1:13 21.1.1.1:13 icmp 15.1.1.1:14 10.1.1.1:14 31.1.1.1:14 31.1.1.1:14 R1# So my question is that after every ip address [:] is used & some number. 15.1.1.1{:11}... what is this colon & number indicate. Can anyone tel me this..!!! Thanking you advance. Shahin

4 Answers  

---

. Which command sequence will allow only traffic from network 185.64.0.0 to enter interface s0? A. access-list 25 permit 185.64.0.0 255.255.0.0 int s0 ; ip access-list 25 out B. access-list 25 permit 185.64.0.0 255.255.0.0 int s0 ; ip access-group 25 out C. access-list 25 permit 185.64.0.0 0.0.255.255 int s0 ; ip access-list 25 in D. access-list 25 permit 185.64.0.0 0.0.255.255 int s0 ; ip access-group 25 in

1 Answers  

---

What are 10base5 ethernet lans?

0 Answers  

---

Which statement is true regarding Administrative distance? A.) It is a metric B.) Number of hops between two routers C.) Trustworthiness of the routing information D.) RIP Administrative distance is 100

1 Answers   TCS,

---

Which command displays all the commands in the history buffer? A. CTRL H B. show buffer C. show history D. show history buffer

2 Answers  

---

What does 'P' mean when running a Trace? A.) Good route B.) Protocol unreachable C.) Source Quench D.) Destination unreachable

2 Answers  

---

What is the most common layer 2 device? A. Hub B. Bridge C. Switch D. Router

20 Answers   IBM,

---

Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay

1 Answers  

---

A router on one side of a PPP link uses the resonance RTR1 and the password COPP1-PWD. Which configuration line on RTR1 enables a connection between RTR1 and another router named RTR2? A. username, RTR2 password COPR1-PWD, B. username, RTR1 password COPR1-PWD, C. username, RTR2 password COPR2-PWD, D. username, RTR1 password COPR2-PWD,

1 Answers  

---

Identify the administrative distance and appropriate routing protocol? A.) RIP = 255, IGRP = 100 B.) RIP = 100, IGRP = 120 C.) RIP = 1, IGRP = 0 D.) RIP = 120, IGRP = 100

3 Answers  

---