Which global configuration command will tell the router to load the IOS file 'IOS_filename' from FLASH memory at the next boot? A.) boot system flash B.) boot system flash IOS_filename C.) boot system IOS_filename flash D.) boot system tftp IOS_filename tftp_address E.) config-register 0x0102 IOS_ filename

2 Answers   HSBC,

---

What is the default IPX Ethernet encapsulation? A.) SNAP B.) Arpa C.) 802.2 D.) Novell-Ether E.) SAP

2 Answers  

---

Which OSI layer incorporates the MAC address and the LLC? A.) Data link B.) Network C.) Physcial D.) Transport

4 Answers  

---

Which of the following are examples of the Datalink Layer? A.) LLC B.) SQL C.) TCP D.) Token Ring E.) IP

2 Answers  

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

Identify the IPX standard access-list number range? A.) 600 - 699 B.) 1000 - 1099 C.) 1 - 99 D.) 100 - 199 E.) 800 - 899

1 Answers  

---

What are the advantages of a layered model in the networking industry?

0 Answers  

---

Which statement about the Committed Information Rate (CIP) is true? A. It is the rate in bits per second at which the Frame Relay switch agrees to transfer data B. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay cloud C. It is the maximum number of bits that switch can transferduring any Committed Rate Measurement Interval D. It is a signaling standard between the 3PE device and FP switch. It is responsible for managing the connection and maintaining status between the devices.

1 Answers  

---

Referring to the commands shown, what command must next be used on the branch router prior to traffic being sent to the router?

0 Answers  

---

intial information of packey occur on which layer application sessions physical mine answer physical

1 Answers  

---

Layer 1 and Layer 2 devices must forward a broadcast. Which of the following devices fall into this category? Gateway Switch Router All of the above.

1 Answers   Sutherland,

---

What is the default CDP broadcast update rate for Cisco routers? A.) 120 seconds B.) 60 seconds C.) 30 seconds D.) 90 seconds

1 Answers  

---