Answer / mithun dashore

Dear Friends it is depend on the configuration what they are
doing ,suppose if you are talking about routing than both
admin configuration will be saved on router but before the
routing router has to be check lowest AD or routing protocol
which has lowest AD Router will send traffic via this
protocol. like this all this depend on the configuration.
he guise listen there is one more think its only based on
CISCO Router. I don't know about any other .

Answer / jitendera

HI
When you are configuring any Router/switch/firewall it will
assign the process id

That is depend upon who log in first and the time difference
might be first log in and second log in is is nano second

so the person who have first Process the router will take
his Conf and fro another user it will throw an error

Device is busy.......please try latter

Suppose we have 4 switches runing in VTP mode. So when i create a VLAN in Server Switch this VLAN info reflect in all other switch. So question is - A) Suppose i m practicing this scenario in BOSON software, When a create a VLAN in server switch n ADD ports of switch to that VLAN, the same number of ports of client switch also belongs to dat VLAN. For example - In switch A (Server mode), i create a VLAN 7 name Hyderabad & port number 1, 2 & 3 put into this VLAN. Another Switch B (Client mode), its also showing that port number 1,2 & 3 belong the same VLAN. How cud it possible... As we know, VTP share only VLAN configuration information. Cud anyone explain it please....!!!! B)Same thing, when i m practicing in PACKET TRACER 5.0, its only showing that VLAN configuration information is shared. No port information is shared at all. I can manually configure individual switch port to respective VLAN as our wish. Cud anyone explain it please..!!!

3 Answers  

---

Which of the following is true? A. The default is to send debug output to the console screen. B. To view debug output from a telnet session, the "terminal monitor" command must be used C. If the "logging buffered" command is used, the debug output would be sent to RAM and can be viewed with the "show log" command D. If the "no console loggin" command were configured, output would besent to a telnet session E. All of the above F. None of the above G. A, B, and C. H. A, C, D, and E.

2 Answers  

---

let threr are three router 1 is cionected to two and two is conected to three that is 1----2----3 now we can ping 2 from 3 and 1 to two but we are not able to ping 1 to 3 let router 1 is local and rest of two are remote what should be urs troubleshoot steps

2 Answers   Volvo,

---

Which can be logged by IPX extended access lists? A.) source address B.) protocol C.) source socket D.) access list number E.) destination socket F.) destination address

1 Answers  

---

Explain the difference between half-duplex and full-duplex?

0 Answers  

---

How does PPTP encapsulate data?

0 Answers   CCIE,

---

Which is true regarding half duplex Ethernet operation? A.) Half Duplex ethernet technology provides a transmit circuit connection wired directly to the receiver circuit at the other end B.) Half duplex transmission between stations is achieved by using point to multipoint Ethernet and Fast Ethernet C.) With Half Duplex transmission logically circuits feed into a single cable creating a situation similar to a one way bridge D.) Half Duplex transmission between stations is achieved using Point to Point Ethernet & Fast Ethernet

2 Answers  

---

In Novell's use of RIP, there are two metrics used to make routing decisions. Select the two metrics. A. Ticks. B. Hops C. Loops D. Counts

3 Answers  

---

Which statement about the Committed Information Rate (CIP) is true? A. It is the rate in bits per second at which the Frame Relay switch agrees to transfer data B. It is the clock speed (pod speed) of the connection (local loop) to the Frame Relay cloud C. It is the maximum number of bits that switch can transferduring any Committed Rate Measurement Interval D. It is a signaling standard between the 3PE device and FP switch. It is responsible for managing the connection and maintaining status between the devices.

1 Answers  

---

What command displays a summary list of OSPF interfaces that includes a column for the cost of each interface?

1 Answers  

---

You would like to have a notation that when a user issues the command 'show interface serial 0', a line is displayed indicating that, 'This is the connection to Company A.' What interface command would accomplish this? A.) banner motd #This is the connection to Company A.# B.) interface This is the connection to Company A. C.) This cannot be done for an individual interface. D.) description This is the connection to Company A. E.) banner This is the connection to Company A. F.) display This is the connection to Company A.

1 Answers  

---

What is DHCP stand for?

0 Answers  

---