Answer / guest

here i am drawing the digram

R1(10.0.1.2/8)--(10.0.1.3)R2(11.0.1.2)--(.3)R3
rip v2 rip and v2 rip

As i know that ripv2 have one diffrence that ripv2 support
the vlsm so here i am not geting any subnated ip so in
first eye it will comunicate

now we have to think about the as value

while configuring the rip v1 or v2 we didnot put the as
value so it is idependent of as value here also we can say
it will comunicate

Answer / satish basa

1) Communication between R1 and R2
solution: R1 can send data to R2 but R1 cannot receive data from R2 (RipV2---->RipV1, only one way possible but Router with RipV2 cannot receive data from Router with RipV1)

2) Communication between R2 and R3
solution: Similarly R2( ripV2) can send data to R3(ripV1) but R2 cannot receive data from R3

Answer / guest

No never, if u r using dis contiguous network RIP v1 not
support. We've to use RIP v2.

Answer / guest

I can't get, can u suggest.

Answer / ranji2011

Hi,

You should configure the RIP version 2 on both the sides. It
will communicate.

Ranji.

Which router command allows you to determine if an IP access list is enabled on a particular interface? A. Router# show ip interface B. Router> show access-list C. Router# show ip access-list D. Router> show interface ip access-list E. Route 1 P.O. box 198

2 Answers  

Identify the command to determine if CDP is enabled? A.) show enable cdp B.) show cdp enabled C.) show cdp run D.) show cdp

1 Answers  

How does the cut-through switching technique work? A.) By using broadcast address as source addresses B.) The switch waits only for the header to be received before it checks the destination address and starts forwarding the packets C.) The LAN switch copies the entire frame into its onboard buffers and then looks up the destination address in its forwarding, or switching, table and determines the outgoing interface D.) By using a Class I repeater in a collision domain

3 Answers  

What is the maximum request timer?

0 Answers  

What does the "IPX maximum-paths 2" command accomplish? A. It enables load sharing on 2 paths if the paths are equal metric paths. B. It sets up routing to go to network 2. C. It is the default for Cisco IPX load sharing. D. It enables load sharing on 2 paths if the paths are unequal metric paths.

3 Answers  

Which layer is responsible for routing through an internetwork? A.) Physical B.) Session C.) Network D.) Transport E.) Application F.) Data Link

4 Answers  

what is the difference between 1 router and switch 2 router and hub 3 hub and switch 4 bridge and switch

1 Answers   Hathway,

wat is last assignable host address in 209.165.201.0/27 network?

7 Answers  

What command do you use to disable domain lookup? A.) no domain-lookup B.) domain no-lookup C.) lookup no-domain D.) no ip domain-lookup

2 Answers  

Which type of LAN segmentation device enables high speed data exchange? A. hub B. bridge C. switch D. repeater

3 Answers   Accenture, TCS,

"arpa" is used by the Cisco IOS for which encapsulation types? A. Ethernet_II B. Ethernet_802.3 C. Ethernet_802.2 D. Ethernet_SNAP

3 Answers   Cisco, Reliance,

When a Distance Vector routing protocol detects that a connected network has gone down, it sends out a special routing update packet, telling all directly connected routers that the distance to the dead network is infinity. This is an example of which routing technology? A.) ICMP. B.) Only Link State routing protocols have this intelligence. C.) Triggered updates. D.) Garrison-4. E.) Split Horizon. F.) Poison Reverse.

1 Answers