Interested to Buy Any Domain ? << Click Here >> for more details...
When designing a flat switched network you can have:
A. the same number of IP and IPX nodes without performance
degradation
B. more IP than IPX nodes on the same segment
C. more IPX than IP nodes on the same segment
D. more AppleTalk than IP nodes on the same segment
- 1 Answers
- 3527 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: A
This is a very deceiving question because all the answers
can be right. Our best guess would be A. If you use the
table below, you can see that in a mixed environment that
the maximum number of workstations that you can use per
segment shouldn?t exceed 200. If that?s the case, we could
have 150 IP workstations and 50 IPX workstations, which
would make B correct. Or, we could have 150 IPX workstations
and 50 IP workstations, which would make C correct. You get
the picture by now. So, we chose A in assuming that you
could have 100 IP workstations and 100 IPX workstations
without performance degradation.
Protocol Maximum Number of Workstations per segment
IP 500
IPX 300
AppleTalk 200
NetBIOS 200
Mixed 200
However, make note of this for the exam: If answer B said
?more IP than IPX nodes on the same segment without
performance degradation? we would have chosen that answer
because there is less broadcast traffic with IP nodes.
| Is This Answer Correct ? | 0 Yes | 0 No |
What device initiates a session in an X.25 network? A. DTE B. DCE C. PSE D. PAD
What category or categories does Client/Server fit into the following Job Aid? Name of Protocol Type of Protocol # of Users # of Hosts or Servers Comments
What is the first step in diagramming packet flow for the terminals within a network? A. Identify the end user nodes of all the terminals B. Figure out the speed of all the servers C. Find out where all the routers are located D. Find out where all the switched are located
Which of the following three sets of IP addresses and subnet masks are private IP addresses? A. 10.0.0.0 255.0.0.0 B. 172.16.0.0 255.255.0.0 C. 172.16.0.0 255.240.0.0 D. 192.168.0.0 255.255.0.0
What are three LAPB features supported by SDLC? A. Frame types B. Frame format C. Field functions D. ABM
What is the technique used by a router that can automatically initiate and close a circuit-switched session? A. PLP B. LAPP C. ASN.1 D. DDR
Which of the following is not true in regards to route summarization? A. It increases the size of the routing table B. It increases the complexity of the network C. IP networks must be contiguous to be safely summarized D. Routing tables must have the capacity to support classless routing
What would a TE2 device be used for in an ISDN connection? A. as a connection from an NT1 device to an NT2 device B. as a connection from a non-ISDN terminal through a TA to the ISDN network C. as a connection from four-wire subscriber wiring to the conventional two-wire local loop D. as a connection to the ISDN network through a four-wire, twisted-pair digital link
Match the following services with the correct descriptions: A. BRI 1. Provides two 64 Kbps B channels B. PRI 2. Provides 23 or 30 B channels 3. Provides one 16 Kbps D channel 4. Provides one 64 Kbps D channel 5. Provides a total bit rate of 2.048 Mbps in Europe and Australia 6. Provides a total bit rate of 144 Kbps 7. Provides a total bit rate of 1.544 Kbps in North America and Japan
What should be looked at first to determine if a customer should switch from a hub environment to a switched environment? A. Investigate the number of broadcasts B. Investigate the number of collisions C. Determine what routing loops are present D. Determine which switching type is being used by the hubs
What task do you complete to identify organizational objectives that will reflect your design? A. Business Objectives B. Scheduling requirements C. Vacation time D. Meetings
when ever we apply show flash comand on the router it givesthat informatin router#show flash syatem file directory: file length name/status 1 8121000 c2500-js-L.112-18.bin what does it nean plz help i have read it from book but not bale to understand i am looking towards u for the help
CCNA 
