Interested to Buy Any Domain ? << Click Here >> for more details...
What happens to performance if the maximum MTU (Maximum
Transmission Unit) size is used?
A. Performance increases
B. Performance decreases
C. Performance stays the same
D. Performance has nothing to do with the MTU
- 1 Answers
- 4786 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: A
Performance should increase when the maximum MTU size is
used. Fewer packets need to be sent if the MTU is at its
maximum.
| Is This Answer Correct ? | 4 Yes | 0 No |
What PPP frame initiates the network layer protocols to be used during a connection?
Match the following services with the correct descriptions: A. BRI 1. Provides two 64 Kbps B channels B. PRI 2. Provides 23 or 30 B channels 3. Provides one 16 Kbps D channel 4. Provides one 64 Kbps D channel 5. Provides a total bit rate of 2.048 Mbps in Europe and Australia 6. Provides a total bit rate of 144 Kbps 7. Provides a total bit rate of 1.544 Kbps in North America and Japan
What are metrics used with IGRP? A. Ticks B. Load C. Hops D. Delay
What is the first step in diagramming packet flow for the terminals within a network? A. Identify the end user nodes of all the terminals B. Figure out the speed of all the servers C. Find out where all the routers are located D. Find out where all the switched are located
What should be looked at first to determine if a customer should switch from a hub environment to a switched environment? A. Investigate the number of broadcasts B. Investigate the number of collisions C. Determine what routing loops are present D. Determine which switching type is being used by the hubs
The following are the four steps in establishing an X.25 virtual circuit. Place them in the correct order. A. The PSE (Packet Switch Exchange) passes the packet to the next remote DCE B. The local DCE packet binder sends packet to the closest PSE (Packet Switch Exchange) C. The source DTE sends packet to the local DCE D. The remote DCE examines the packet header of destination DTE
Which two statements correctly identify considerations to take into account when deciding on campus QoS Design elements ?
How can change k-value in EIGRP configuration.
Which condition does not create LAN media problems? A. Protocol doesn?t scale well B. Long wait for the token C. Excessive collisions D. Too many devices
How can I release the restriction of CISCO2811C/K9? 10M optical fiber, Speed limit of 125kb / s, made by last network administrator, how can I release the restriction? Please tell me the detail, thanks! Cisco configuration： CISCO2811C/K9 ! ! ! ! ! ! ! interface FastEthernet0/0 description WANpork ip address x.x.x.x 255.255.255.248 ip access-group 110 in no ip proxy-arp ip verify unicast reverse-path ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1 description LANpork ip address 192.168.x.x 255.255.255.0 ip access-group 101 in no ip proxy-arp ip verify unicast reverse-path ip nat inside ip virtual-reassembly rate-limit output 1000000 1000000 1000000 conform-action transmit exceed-action drop duplex auto speed auto !
What is an advantage of CHAP over PAP? A. Passwords are stored on separate servers in encrypted form B. CHAP sends passwords unencrypted to save connection time C. CHAP does not attempt to verify whether the user is authorized to access the requested resource D. ID?s and passwords are automatically stored in cache
Which two of the following describe ASN.1 (Abstract Syntax Notation One)? A. It is an abstract routing protocol that is not used very often. B. It is an OSI language for describing data types independent of particular computer structures and representation techniques. C. Consists of only one basic routing algorithm. D. Uses BER (Basic Encoding Rules).
CCNA 
