What are two ways IPX supports multiple logical networks on
an individual underrate? (Choose two)
A. network number
B. routing protocol
C. encapsulation type
D. autonomous system number
- 1 Answers
- 3361 Views
- I also Faced
- E-Mail Answers
What is the purpose of ARP? A.) IP to host name resolution B.) Host name to IP address resolution C.) Mac to IP address resolution D.) IP to Mac address resolution
hi friends i am jitendera kumar sinha.i have a question in mind that what is the diffrence between router and l3 switch i serched on google and found that switch L3 is best in lan and router are best in wan and switch are more faster then router.beside that any short of technical diffrence if you body know then plz plz and plz reply. my 2nd question is that why we canot replace router with L3 switches (donot tell that it is costly then router).i want any technical cause. this is 1 am hope in noon when ever i logg again i will find the answer posted by you. thanks onse again plz pzl make reply thanks jitendera kumar sinha jitenerasinha.it@gmail.com
what is hop count?
Identify the 2 commands that save the running-config to a TFTP server? A.) write running tftp B.) copy running network C.) copy running tftp D.) write network
Given the global configuration commands: 'banner motd #' 'Hello #' When would the message be displayed? A.) The message of the day banner shows up before login. B.) The message of the day banner shows up during logoff. C.) These commands are not the right syntax for MOTD. D.) Message of the day banners are displayed upon entering global config mode. E.) Message of the day banners are not possible. F.) The message of the day would be, 'Hello #'
Which works router do?
Which of the following use PVCs at layer 2? A.) X.25 B.) HDLC C.) Frame relay D.) ISDN
Based upon the 1st octet rule identify the range for a Class A address? A.) 1 - 126 B.) 192 - 223 C.) 128 - 191 D.) 1 - 191
Which of the following are valid Cisco encapsulation type names? A.) arpa = IPX Ethernet B.) novell-ether = IPX Ethernet_802.3 C.) snap = IEEE 802.2 SNAP on Ethernet, FDDI, and Token Ring D.) novell-fddi = IPX Fddi_Raw E.) sap = IEEE 802.2 on Ethernet, FDDI, and Token Ring F.) hdlc = HDLC on serial interfaces
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
What is the difference between switch and hub?
Why subnetting is used?
CCNA 
