Answer / guest

Answer: D

Answer / s.m.feroz ahmed

Hi,
D. copy tftp flash will load new version of IOS to Router.

Identify the command that saves the configuration stored in RAM to NVRAM? A.) copy running-config startup-config B.) copy tftp running-config C.) copy startup running D.) copy active to backup

2 Answers  

---

what is Bandwidth capping

0 Answers   Infosys,

---

Identify the purpose of ARP? A.) Avoiding routing loops B.) Determining a workstation's IP address C.) Sending a directed broadcast D.) Determining a workstation's MAC address

3 Answers  

---

Which show command should you use to view Frame Relay Local Management Interface (LMI) Frame statistics? A. show lmi B. show ip route C. show interface D. show statistics E. show frame-relay lmi

1 Answers  

---

CSMA/CD stand for which of the following? A.) Carrier Sense, Multiple Access with Collision Detection B.) Collision Sense, Multiple Access with Collision Detection C.) Collision Sense, Multiple Access with Carrier Detection D.) Carrier Sense, MAC address with Collision Detection

1 Answers  

---

how will configure Nat

6 Answers   Spanco,

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

1 Answers  

---

Utilizing RIP, what is the limit when it comes to number of hops?

0 Answers  

---

What is the difference between named and extended acl?

0 Answers  

---

Which show underrate serial 1 status statement indicates that the shutdown command was issued on that interface? A. Serial 1 is up line protocol is up B. Serial 1 is up line protocol is down C. Serial 1 is down line protocol is down D. Serial 1 is administratively down the line protocol is down

2 Answers   Pioneer Labs,

---

Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!

5 Answers  

---

9. Which STP state prevents the use of looped paths? A. Blocking B. Listening C. Learning D. Forwarding

2 Answers  

---