Answer / guest

Answer: A E

Central Office (CO) - A switching facility that provides the
nearest

point of presence for a provider's WAN service.

Demarcation (Demarc) - The point at which the CPE ends and
the local

loop portion of the service begins. Usually the
telecommunications

closet at the subscriber's location.

CPE, DTE, DCE, and the router are all typically owned by the
customer.

DTE devices are usually routers, DCE devices are CSUs/DSUs,
or WAN

interfaces that have a built in CSU/DSU in the router. CPE
stands for

Customer Premise Equipment.

Which Circuit is mostly used by Clients in Frame-Relay PVC or SVC ?

5 Answers   TATA,

---

while trouble shooting a network conectivty prob a technician observes that steady link light on the both work stations nic and the switch port which the workstation is conected.however when the ping comand is issuede from the work station the out message is request time out at which layer of osi model does the prob most likly exist 1 sessiom layer protocol layer datalink kayer acess layer network layer application layer i have ansered n/w layer but i am niot sure i have also posted privous question jitendera kumar sinha

3 Answers  

---

Which of the following is true? A. The default is to send debug output to the console screen. B. To view debug output from a telnet session, the "terminal monitor" command must be used C. If the "logging buffered" command is used, the debug output would be sent to RAM and can be viewed with the "show log" command D. If the "no console loggin" command were configured, output would besent to a telnet session E. All of the above F. None of the above G. A, B, and C. H. A, C, D, and E.

2 Answers  

---

What is the function of Layer 2 Switch?

4 Answers   Amazon,

---

Which protocol works only on cisco routers?

1 Answers  

---

How does rip differs from igrp?

1 Answers  

---

How many networks route update does a router recieves in RIP at once ?

3 Answers   ComNet,

---

Identify the 3 guidelines for routers in the same autonomous system? A.) Must be configured for RIP B.) Interconnected C.) Assigned the same autonomous system number D.) Configured for the same routing protocol E.) Must be same model of router

1 Answers  

---

What is true when creating static route? A.) The mask parameter is optional B.) The administrative distance is required C.) The gateway parameter is required D.) The administrative distance is optional

1 Answers  

---

What is the diiffernce between windows xp & windows 2000?

6 Answers   TCS, Trimax, Trymax, VigaTech,

---

take a pen and copy before solving that question there is a router name Ra there is two switch sw1 and sw2 sw1 is coneceted through fa0/1 interface of router Ra sw2 is conected through the fa1/1 serai interface of router s0/1 conected through the isp with it ip address 192.168.1.1 now therer are three host conexted through the sw1 and having ip host1=10.1.2.1 host2=10.1.2.2 host3=10.1.2.3 now there is also 3ree host conected through switch 2 i.e sw2 having ip host4=10.1.1.1 host 5=10.1.1.2 host 6=10.1.1.3 now i think u have made corect confrigation.now questios is started network admin configure the Ra router in that fassion Ra(config)#access-list 2 permit 10.1.1.0 0.0.0.255 Ra(config)#line vty 0 4 ra(config)#access-class 2 in now question is that why should network admnistratoe do it in this maneer A to give access sw1 host to acess internet B to prevent sw1 host from acessing comand promt c to prevent sw2 host from accessing console of router ra D to give sw2 host access to the enternet e prevent sw1 host from accessing internet f to prevent sw1 host from acessing the sw2 host network isp------(s0/1)..RA..(fa1/1)---SW2-host (4,5,6) | | (sw1)------host 1,2,3 this is not exect digarm but help to derive the diagram plz answer as soon as possible

6 Answers   AT&T,

---

hi friends i donot know this is the networking question or not but if you help me then i will thankfull to you the problem is like that in my comnay there are 200 user which log one at a time now only one user is not able to get the dhcp address and othr are geting the dhcp my company sys admin is saying that this is the n/w fault while i am saying that this is not the n/w fault for the cleaerfication of my side i take a straight workng cable and connect that user directly to my cisco 24port switch now problem is stiil like that but one thing i wan to say he is geting manually ip and able to access internet he is able to ping the server but whrnever he tyeme \\<ip address of server> error comes like networl path provided not accepted by provider some thing like that. my systm admin is saying that i have o do somthing on my firewall but i am saying that no issue with firewall in that i connect my latop to the spefic port from where the user is conected then i am geting dhcp ip address and i am able to connect the server also i donot know why this is happen my syadmin is senior to me so i canot blame him plz help e what to do i am very weak in the filed of systym jitendera kumar sinha

6 Answers  

---