Interested to Buy Any Domain ? << Click Here >> for more details...
Identify the 3 characteristics of IGRP?
A.) Uses hop count as a metric
B.) Supports multiple unequal paths
C.) Administrative distance is 100
D.) Configured with an Autonomous system number
E.) Link state
- 1 Answers
- 3620 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: B C D
IGRP is a distance vector routing protocol, it's degree of
trustworthiness is 100, it can support up to 6 un-equal
paths and must
be configured with an autonomous system number.
| Is This Answer Correct ? | 2 Yes | 0 No |
Put the following steps of encapsulation into the correct order: 1) The data is broken into segments to be organized 2) Frames are converted to 1s and 0s to be put on the wire 3) Packets are converted into frames 4) Information that users enter is converted into data 5) The segments are changed to packets to be routed A.) 4, 1, 3, 2, 5 B.) 4, 5, 1, 3, 2 C.) 2, 3, 1, 4, 5 D.) 4, 1, 5, 3, 2
I am facing one problem in my layer 2 switch I don’t know the problem is on switch side or client side. The problem is some PC (not all) are stop participate in LAN they don’t send or recd. Packet from switch and if I check RJ45 (with LAN tester)from PC side the packet and 8 pin wire is working fine and after that process of LAN tester I plug RJ 45 in PC now PC start recd/ send packets what is the problem I don’t understand even client side no virus found RJ45 is ok and switch has no problem bcoz other PC is working fine Cable (cat 5 ) is also fine bcoz I didn’t crimp again just check in LAN tester and start working fine. Plz any one solve this matter. And after lan tester process pc is working fine and after 2 or 3 hour it again start same problem and again same process lan tester I have used
What is matric?
What is true about frame-relay DLCI? A.) DLCI represents a single physical circuit B.) DLCI is optional in all frame-relay networks C.) DLCI identifies a logical connection between DTE devices D.) DLCI is used to tag the beginning of a frame with VLAN information
What is the Difference between Hub and Switch?
As system administrator, you type "debug ipx sap" and receive the following lines as part of the IOS response: type 0x4, "HELLO2", 199.0002.0003.0006 (451), 2 hops type 0x4, "HELLO1", 199.0002.0003.0008 (451), 2 hops What does "0x4" signify? A. That is a Get Nearest Server response. B. That it is a General query. C. That it is a General response. D. That it is a Get Nearest Server request.
Explain the term 'multicast'.
what are layer hierarchy of cisco
Guys Please send me or suggest me any link for all interview question and answer on CCNA asked in TECH MAHINDRA. I have only 4-5 days for preparation. my mail id is nikhil9823@gmail.com
Which IP host address range is allowable given an IP address of 172.37.2.56 and 12 bits of subnetting A. 172.37.2.48 to 172.37.2.63 B. 172.37.2.48 to 172.37.2.62 C. 172.37.2.49 to 172.37.2.62 D. 172.37.2.49 to 172.37.2.63 E. 172.37.2.55 to 172.37.2.126
The command "show IP protocol" displays which information? A. routing timers B. network information C. contents of the IP routing table D. information about all known network and subnetworks
Which command should you use to confound a router so that it can become a TFTP server host for a router system image that is run in a Flash? A. copy flash tftp B. config tftp server C. write, network -router name- D. tftp-server system -file name- E. setup server tftp -system name-
CCNA 
