Interested to Buy Any Domain ? << Click Here >> for more details...
Identify 3 characteristics of the Network layer (OSI layer 3)?
A.) Connection oriented
B.) Path determination
C.) Supports multiplexing
D.) Manages sessions
E.) Packet forwarding
- 4 Answers
- 11968 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / guest
Answer: B C E
The network layer is responsible for routing which entails
learning the
paths, selecting the best path and forwarding the packet.
Because it
services multiple layer 4 protocols it multiplexes.
| Is This Answer Correct ? | 14 Yes | 0 No |
Answer / kelly
B - Path Determination
C - Supports Multiplexing
E - Packet Forwarding
| Is This Answer Correct ? | 1 Yes | 0 No |
What do we check while configuring the server?
What is the subnet? Why is it used?
Which of the following is used to manage and monitor the network? A.) SNMP B.) HTTP C.) IP D.) FTP
"sap" is used by the Cisco IOS for which encapsulation types? A. Ethernet_802.2 B. Token-Ring C. FDDI_SNAP D. Ethernet_802.3 E. FDDI_802.2
What is a benefit of a virtual LAN (VLAN)? A. It increases the number of broadcast domains B. It decreases the number of broadcast domains C. It increases the numberr of collision domains D. It decreases the number of collision domains E. Since it is a vitual Interface it never shuts down
Default packet size of ipv6?
What are the Timer of RIP, IGRP, EIGRP and OSPF Routing Protocol?
Which port numbers are used by TCP and UDP to set up sessions with other hosts? A.) 1024 and above B.) 6 and 17 respectively C.) 1-25 D.) 6-17
what is eigrp and what is the benfit of eigrp over igrp what is route summryization if one the router route is not showing the what should be problem how to resolve these problem what is fessible suceer. is the load balncing is one of the property of eigrp what is the metihod of authantication what is the diffrnec betwee pap and chap what is stp command for enabling stp and rstp why switching loop occur what is the main factor of ocuring switch loop what is the mechnaism for stoping the roting loop what is best diffrence betwwen ospf v1 nad ospf v2 what is vtp what is the diffrence between vtp version 1 and veron 2 what is the ip address what is the diffrence betwwen ip address mac address what is dhcp and how it work what is 3 way hand shake what is the difrence betwwen network id and brodcast id what is the network id for 111.111.111.10/29 what is the command for enabling vlan on 3650 csco switch
Explain the types of communication in ipv6 ?
what is ip address?
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
CCNA 
