1. Categories >> Certifications >> Cisco Certifications >> CCNA
  2. Suggest New Category

Identify the command that will display the RIP routes
entering and

leaving the router?

A.) Router(config)# debug ip rip

B.) Route# debug ip rip

C.) Router>debug ip rip

D.) Router# debug rip routes

Question Posted / guest


Identify the command that will display the RIP routes entering and leaving the router? A.) Ro..

Answer / guest

Answer: B

Is This Answer Correct ?    1 Yes 0 No

Post New Answer

More CCNA Interview Questions

Which three of the following are true statements about connection-oriented sessions? A.) The segments delivered are acknowledged back to the sender upon their reception B.) Any segments not acknowledged the are retransmitted by the receiver C.) A manageable data flow is maintained in order to avoid congestion, overloading and loss of any data D.) Segments are sequenced back into their proper order upon arrival at their destination

1 Answers  

What is the meaning of PASSIVE interface in RIP, IGRP, EIGRP & OSPF?? Can any one explain..!!!

6 Answers  

Can you explain IKE phases? Can you explain IKE modes?

1 Answers   CCIE,

Why we used Virtual MAC in GLBP

0 Answers   Infosys,

As a system administrator, you want to debug igrp but are worried that the "debug IP igrp transaction" command will flood the console. What is the command that you should use? A. debug IP igrp event B. debug IP igrp-events C. debug IP igrp summary D. debug IP igrp events

1 Answers  




Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  

What is Transport and Tunnel mode?

0 Answers   CCIE,

What is the default bandwidth size of t1 routers?

0 Answers  

Suppose we are having two Switches i.e. Switch1 & Switch2 Port1 of Switch1 is Connected to Uplink and switch2 is also connected to switch1? So 1>Is there is any loop? 2>How we come to know that there is a loop created? 3>If we add Switch3 to switch2 then there is a possibility of loop Creation?

0 Answers  

Of the following, which reason applies to dividing a large network into two or more smaller networks? Performance Security Address Management All of the above

2 Answers  

what is subnet mask?

5 Answers   HCL,

What command will not display the status of to1? A.) show int to1 B.) show to1 C.) show interface to1 D.) show interface

1 Answers  

For more CCNA Interview Questions Click Here
Categories