One dataset is creating in the step1 with LRECL of 133 and
the same dataset is used in the next step in DISP=SHR mode,
but while scanning the JCL the following error is thrwon.
Please verify the below JCL
$/SEPP030.PROVIDER DD
DSN=Z1225BT.F5750PG9.F5910PRV.QC#A6868
//ERRORRPT DD
DSN=F5910&ST&IN..F5910EPP.ERRORRPT.P&CYCDATE,
--ERRORRPT DD
DSN=F5910PG.F5910EPP.ERRORRPT.P,
//
DISP=&DISNCD,UNIT=&DELQ,
-- DISP=
(NEW,CATLG,DELETE),UNIT=DELQ,
// SPACE=(TRK,
(30,15),RLSE),
//
DCB=&DCB2
-- DCB=
(PPG.METMODEL,BLKSIZE=0,LRECL=133,RECFM=FB)
$/SEPP030.ERRORRPT DD
DSN=Z1225BT.F5910EPP.ERRORRPT.AOUTPUT
//SEPP040 EXEC PGM=FILEAID,COND=
(0002,EQ,SEPP030)
//SYSPRINT DD
SYSOUT=*
//SYSLIST DD
SYSOUT=*
//DD01 DD DSN=SYSCMN.PROD.CCLIB
(F5910EP1),DISP=SHR
$/SEPP040.DD01 DD DSN=Z1225BT.TEST.CCLIB
(F5910EP1)
E1 - DSS20791E - DATA
SET 'Z1225BT.F5910EPP.ERRORRPT.AOUTPUT' HAS AN
LRECL OF 133 COULD NOT BE OPENED BECAUSE
THE CODED
LRECL WAS
80.
// DD
DSN=F5910&ST&IN..F5910EPP.ERRORRPT.P&CYCDATE,
-- DD
DSN=F5910PG.F5910EPP.ERRORRPT.P,
//
DISP=SHR
$/ DD
DSN=Z1225BT.F5910EPP.ERRORRPT.AOUTPUT
please find the error code in the above mentioned lines and
please suggest me about the error and the solution for that.
Answer Posted / arjun
Actually BLKSIZE is coded as 0 .I think BLKSIZE should
always be coded in multiples of LRECL.i.e; LRECL=133 then
BLKSIZE=1330 should be coded.
Is This Answer Correct ? | 0 Yes | 1 No |
Post New Answer View All Answers
I want to JCL sort for Non-COMP and COMP-3 fields SORT FIELDS=(1,5,A,6,11,A,12,11,A,19,1,A,20,1,A),FORMAT=BI,EQUALS Length of comp bytes is 11 bytes which start at 6byte and 12 byte considering 11 bytes in comp-3 is 6 bytes. Can anyone tell if the above sort work SORT FIELDS=(1,5,A,6,6,A,12,6,A,19,1,A,20,1,A),FORMAT=BI,EQUALS does not works OK
What are the 2 types of parameters in dd statement?
what are the types of abends that occur on job failure? And explain the possible causes of these
Explain the function of //jcllib statement?
What is the job entry system used in your project? based on what criteria the sequence of jobs are picked if priority is not mentioned in the job card?
What are the parameters that are used in creating a gdg?
How do you access an uncatalogued dataset in a jcl?
How to alter the parameters for the existing gdg?
a dd statement has 2 types of parameters. Name them?
Where & How Do You Code Identifier In Jcl?
a set statement is used to define commonly used symbolic across job steps or procedures. It initializes the previous values in the symbolic names. It has to be defined before the first use of the symbolic names in the jcl. State whether true or false?
Can I send output of job to my remote device careerride123?
I have a COBOL program that ACCEPTs some input data. How do you code the JCL statement for this?
What do you understand by the term job time – out and how can you overcome that?
what operation is performed by job statement?