Why do some of the latest 'single crystal' superalloys contain concentrations of the grain boundary strengthening elements, e.g. carbon and boron?

1958

What is a good estimate for the absolute roughness for epoxy lined carbon steel pipe?

4822

where do plants get carbon from and where does the carbon go when plants die?

1896

How does stomatal conductance increase in an elevated carbon dioxide environment?

1832

Why is the t-butyloxycarbonyl protecting group such a good choice for amino acid synthesis?

2076

Describe briefly how an amobea exchanges oxygen and carbon dioxide gases with its surroundings.

2028

I have given the protocol for the cyclodextrin glygosyl transferase assay: One ml of appropriately diluted enzyme sample was incubated at 60 °C for 15 min with 5 ml of 1% (w/v) gelatinized soluble starch in 50 mM, 7.0-pH Tris–HCl buffer. Reaction was terminated by boiling the reaction mixture for 3 min and reaction volume was made to 10 ml with distilled water. Two ml of above reaction mixture was withdrawn and mixed with 3 ml of Tris–HCl buffer, 5 ml of 125 mM Na2CO3, and 0.5 ml of phenolphthalein (25 mg phenolphthalein/100 ml absolute alcohol). Absorbance was measured at 550 nm. The percent decrease of sample was calculated with respect to control containing 5 ml of buffer, 5 ml of sodium carbonate and 0.5 ml of phenolphthalein. where Acontrol = absorbance of control and Atest = absorbance of sample. The amount of β-cyclodextrin (β-CD) produced was estimated from the standard graph of 0–500 μg/ml β-CD concentration against % decrease in absorbance. One unit of CGTase was defined as the amount of enzyme required to produce 1 μm of β-CD/min. Please can you suggest me the formula for the defination given in the last line

2156

is the carbon dust collected from the stask of diesel set is hazardous waste ?

2337

state the disadvantages of carbon filament???

2850

draw IRON-CARBON diagram.

3869

X is strong but has a very low density (1% of traditional earth materials.) and hence light weight. It is a recyclable material. The compression behaviour of X is strain rate dependent. Higher strain rates result in higher initial modulus and higher compression strength. It can also withstand unlimited number of cycling loading provided the repetitive loads are kept below 80% of the compressive strength. The internal structure of the material includes air-traps which make it poor heat conductor. X is non- biodegradable and chemically inert in both soil and water. Most acids and their water solutions do not attack it; however strong oxidizing acids do. Solvents which attack X include esters, ketones, ethers, aromatic and aliphatic hydrocarbons and their emulsions, among others. It does not support bacterial/fungal growth as well .It also has significant acoustic properties and effectively reduces the transmission of airborne sound. X is combustible and should not be exposed to open flame or other ignition sources. Combustion products are carbon monoxide, carbon dioxide, water and soot. Long-term exposure to sunlight causes yellowing and a slight embrittlement of the surface due to ultraviolet light. X is able to withstand the rigours of temperature cycling, assuring long-term performance.

1866

what are carbondioxide and dcp used in fire extinguishers

2010

on interface level transmitter model(RTG3302-EMERSON) What is threshold valve how can we select correct threshold value T1,T2,T3,T4 When interface water & hydro carbon

2104

We are using Rosemount 5400 series Radar Level Transmitters in all types of Sump Applications having oily water hdrocarbon petrochemical nature. What we are facing the problem frequently is that always getting reading frezzed at some value. If we do power recycling , sometimes it is working . then making same freezing problem. If anybody faced before such type of problem and also having solution , Please give the answer.

2289

What is the difference between cracking, pyrolysis, destructive distillation, hydroforming, carbonization and dry distillation?

9742