can we measure how much a host exact bandwidth using by a
network cable which is communicating over the network?
options: 1- via Router 2- Switch, 3- other device... if
yes.. then how ( with every option)

Answers were Sorted based on User's Feedback



can we measure how much a host exact bandwidth using by a network cable which is communicating over..

Answer / gt

I dont want to use any third party software..as you are
saying ..

Is This Answer Correct ?    1 Yes 0 No

can we measure how much a host exact bandwidth using by a network cable which is communicating over..

Answer / jitendera sinha

yed you can do it

for router

enable snmp on the router

dowlad network montering software like solarwinds

then you can monter and take logs of each network cable
over networl

for switch smae way as router

for another dievise use prtg bandwidhth monitor

Is This Answer Correct ?    0 Yes 0 No

can we measure how much a host exact bandwidth using by a network cable which is communicating over..

Answer / jitu

hi gopal ji
how cna you measure yours body temp with out any externel aggent
is it possible?

no

so to monitor or measure you should use the external agent
this is the simple way.

if you got any alternate soln the plz post it here

6 + 3 = 9(why this is ask each time)

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

what is the default ad value of the interface directly coneted to router. as for exmaple ad value of ospf is 90 then from ehternet the network is conected whta is difault value of that directly conected interface. what is the defalt ad value of bgp whta is access llist and how many type of access list what is vlan what is vpn how e congigure the router what is mpls these are the question skrd to me at tcs i have replyed all ecxept the first one

1 Answers   TCS,


What is osi?

0 Answers  


In order to configure a Frame Relay subinterface with IP identify the 2 commands that must be configured on the physcial interface? A.) Router(config-if)# encapsulation frame-relay B.) Router(config-if)# no ip address C.) Router(config-if)#encapsulation subinterface frame-relay D.) Router(config)# subinterface s0 encapsulation frame-relay

2 Answers  


which algorithm as defined by the transform set is used for providing data confidentiality when connected to tyre?

0 Answers  


WHY DO WE USE the command interface Vlan 1 ip adress x.x.x.x sub mask what does it do .. what does it create.. i know when we create it we can remotely telnet inti a router=switch. but what is the diff bwt vlan and intface vlan. ... vlan 1 bieng a native vlan remains there eve if i dont gv switch an ip address .. lease suggest.

1 Answers   Wipro,






What are the advantages of layered model in networking industry?

0 Answers  


What does the IPX maximum path command do? A.) Allows you to disable the TTL on an IPX packet B.) This parameter is only used in NLSP routing C.) Sets the maximum metric that can appear in the routing table D.) Configures round robin load sharing over multiple equal metric paths (parallel paths)

1 Answers  


In order to limit the quantity of numbers that a system administrator has to enter, Cisco can use which abbreviation to indicate 0.0.0.0? A. host B. any C. all D. include

1 Answers  


Where shall i do CCNA cour??. can i do CCNA at home if yes then where shall i get CCNA book or simmulator.or if not then plz reff. me any good center in delhi

1 Answers  


1 whatis te1,te2 and nt1 what is threre functions 2 what are the isdn protocols 3 whait is spid

1 Answers  


What is convergence time? A.) The update time B.) The time it takes to reload a router C.) The time it takes for a packet to reach its destination D.) The time is takes for all routers update their tables after a change takes place

2 Answers  


1) How a router established a neighbor relation ship in ospf

1 Answers   Infosys,


Categories