Identify the length of an IPX address and it's components? A.) 80 bits, 48 bits network and 32 bits node B.) 32 bits, 16 bits network and 16 bits node C.) None of the above D.) 80 bits, 32 bits network and 48 bits node

1 Answers  

---

HI I am Rajveersinh. I am Leaving in Ahmedabad-gujarat. I am Hardware & Networking Stundent In JETKING. my Intersted in CICKO Side. Please send ME totel detail in CICKO surtifiction my E-mail ID IS as_raj@ymail.com

6 Answers   HCL,

---

What is topology in ccna?

0 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

4 Answers  

---

Identify the OSI layer associated with bits? A.) Physical B.) Network C.) Binary D.) Data link

2 Answers  

---

---

How we can find ASBR Router, we have no authentication to enter router?

3 Answers   Logica CMG, Wipro,

---

How would you set the clock rate to 64K, on interface serial 0, from the interface configuration mode? A.) clock rate 64000 B.) bandwidth 64 C.) clock 64 D.) rate 64 E.) clock rate 64k F.) clock rate 64

1 Answers  

---

What is raid in ccna?

0 Answers  

---

Name the command we give for see routing table?

0 Answers  

---

Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!

5 Answers  

---

Which two encapsulation names are correctly paired with the Cisco IOS encapsulation names? (Choose two) A. Ethernet_II-ARPA B. Ethernet_802.3-SAP C. Ethernet_802.2-LLC D. Ethernet_SNAP-SNAP

1 Answers  

---

A default route is analogous to a _________. A. default gateway B. static route C. dynamic route D. one-way route

1 Answers  

---