Interested to Buy Any Domain ? << Click Here >> for more details...
How to crimping cat cable without using crimping and any
tool...........?
- 6 Answers
- 11867 Views
- CTS, Wipro, I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Answer / reddy
It,s not at all possible without crimping tool..
| Is This Answer Correct ? | 44 Yes | 5 No |
Answer / st ahamed
the word crimp is apractical job done with the help of a
tool .It can not be done with out tool.
| Is This Answer Correct ? | 21 Yes | 4 No |
Answer / umar
By using crimping tool is the best way,man handling may be success or may not.... no guarantee.so go for crimping tool..
| Is This Answer Correct ? | 8 Yes | 3 No |
Hi Respected all,
It is possible, we can crimping cat cable without crimping
tool.
let me tell you....it is depends upon the product like
AMP,tyco and R&M ect........
R&M mostly introduce the tool free product, if you are
using R&M i promised you can crimping cat cable without
crimping tool.
| Is This Answer Correct ? | 3 Yes | 1 No |
Answer / raj thakur
well, if it is an emergency and you need to do it anyhow..
then first pile the cable with the help of a knife and
blade.. note that you must need to be alert while doing this
otherwise you can cut any link or yourself.. then put it in
RJ-45 connecter and press hard in middle so connecter could
fix on it.
| Is This Answer Correct ? | 6 Yes | 7 No |
Which of the following is a characteristic of a switch, but not of a router? A.) Switches forward packets based on the IPX or IP address in the frame B.) Switches forward packets based on the IP address in the frame C.) Switches forward packets based on the MAC address in the frame D.) Switches forward packets based only on the IP address in the packet
What is BGP Synchronization rules?? Can any one explain..???
Explain the types of communication in ipv4?
Which of the following would not be displayed by the command ?sho cdp neighbor detail?? A.) The incoming/outgoing interface. B.) The hardware platform. C.) One address per protocol. D.) Amount of Flash Memory Available E.) The routers hostname. F.) The subnet mask, if IP is configured.
can any budy send the steps for enabling snmp on cisco switches(L2).
Which global configuration command will tell the router to load the IOS file 'IOS_filename' from the Network File server at 1.2.3.4 during the next boot? A.) boot system flash IOS_filename 1.2.3.4 B.) boot system tftp IOS_filename 1.2.3.4 C.) config-register 0x0 1.2.3.4 D.) boot system rom 1.2.3.4 E.) This can not be done, only the first file in flash can be used.
What are the job opportunities i will get once i complete my CCNA certification.
What is size of ipv4 mac address?
Which three functions are supported by connection oriented servkps? (Choose three) A. connection parameters are synchronized B. any loss or duplication of packets can be corrected C. the data packet is independently routed and the service does not guarantee the packet will be processed in order D. a data communication path is established between a requesting entity and the peer device on the remote end system
What is the bit length and expression form of a MAC address? A. 24 bits expressed as a decimal number B. 24 bits expressed as a hexadecimal number C. 36 bits expressed as a binary number D. 48 bits expressed as a decimal number E. 48 bits expressed as a hexadecimal number
What does the term Base refer to in 100BaseT A. cabling type B. singnal type C. 100 mode type D. spectrum used E. speed category
Identify the protocol to test connectivity without configuring any layer 3 protocols? A.) TCP B.) Ping C.) IP D.) CDP E.) Telnet
CCNA 
