What does -1 mean in an extended IPX access-list?

A.) Any IP address

B.) Deny all

C.) Deny host

D.) Any host or any network



What does -1 mean in an extended IPX access-list? A.) Any IP address B.) Deny all C.) Deny ..

Answer / guest

Answer: D

Is This Answer Correct ?    0 Yes 0 No

Post New Answer

More CCNA Interview Questions

what is internetworking.

6 Answers  


Can you explain PPP link process step by step?

0 Answers   CCIE, Sawes,


Given an IPX network with redundant paths, what command will configure load balancing? A.) ipx load-balance B.) ip maximum-paths 2 C.) ipx maximum-paths 2 D.) ipx load-share

1 Answers  


Explain the difference between collision domain and broadcast domain.

0 Answers  


What is the default switching method for the Cisco 5000 series? A.) Cut-through B.) Store-and-splice C.) Latency D.) Store-and-forward

1 Answers  






We have one router,we r using two routing protocol eigrp 90 net 1.1.1.0/16, ospf 110 net 1.1.1.0/24 on same router, Is it possible?

6 Answers   Wipro,


Which port numbers are used by TCP and UDP to set up sessions with other hosts? A.) 1024 and above B.) 6 and 17 respectively C.) 1-25 D.) 6-17

6 Answers  


Identify the administrative distance and appropriate routing protocol? A.) RIP = 255, IGRP = 100 B.) RIP = 100, IGRP = 120 C.) RIP = 1, IGRP = 0 D.) RIP = 120, IGRP = 100

4 Answers  


Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..

6 Answers  


The Cisco IOS is stored where? A.) ROM B.) CD C.) Flash D.) NVRAM

1 Answers  


Which command would configure Interface E0 with an IP address of 12.23.4.5 using a Subnet mask of 255.255.255.0 ? A.) ip address 12.23.4.5 255.255.255.0 B.) ip address 12.23.4.5 /24 C.) ip address 12.23.4.5 mask 255.255.255.0 D.) ip address 12.23.4.5 mask ff:ff:ff:0 E.) that is an invalid mask for a class 'A' address

3 Answers   Wipro,


What 2 commands verify end to end communications? A.) Trace B.) debug ip session C.) Ping D.) Route

2 Answers  


Categories