Which OSI layer defines end to end communication,
segmentation and
re-assembly?
A.) Network
B.) Transport
C.) Physical
D.) Application
E.) Data-Link
F.) Presentation
- 1 Answers
- 5781 Views
- I also Faced
- E-Mail Answers
Identify the statement which connects access-list 101 inbound to interface e0? A.) Router(config-if)# ip access-group 101 in B.) Router(config-if)# ip access-group 101 C.) Router(config)# ip access-group 101 e0 in D.) Router(config)# ip access-group 101 e0 in
What are hold-downs used for? A.) To prevent regular update messages from reinstating a route that has come back up B.) Information received on an interface cannot be sent back out the same interface C.) To prevent regular update messages from reinstating a route that has gone down D.) To hold the routing table from being sent to another router
The ICMP (referred to in RFC 1700) is implented by all TCP/IP hosts. A. true B. false
The Datalink Layer is broken down into 2 layers, LLC and MAC. The LLC establishes media independence and what else? A.) Provides Windowing. B.) Provides flow control. C.) Provides SAP's (Service Access Points). D.) The Datalink layer does not have sublayers. E.) Provides SAP's (Service Advertising Protocol). F.) RIP Updates.
Explain the difference between arp and rarp?
What does the following series of commands accomplish? router igrp 71 network 10.0.0.0 router igrp 109 network 172.68.7.0 A. It isolates networks 10.0.0.0 and 172.68.7.0. B. It loads igrp for networks 109 and 71. C. It disables RIP. D. It disables all routing protocols.
Which updates called incremental updates?
How does cut-through LAN switching work?
What is wide-mouth frog?
What are two ways IPX supports multiple logical networks on an individual underrate? (Choose two) A. network number B. routing protocol C. encapsulation type D. autonomous system number
What is the command to allow you to type Tokyo instead of the IP address 172.16.30.1 to access a router named Tokyo? A.) config t, ip host Tokyo 172.16.30.1 B.) config t, ip hostname Tokyo 172.16.30.1 C.) config t, hostname Tokyo 172.16.30.1 D.) config t, ip hostname 172.16.30.1 Tokyo
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..
CCNA 
