Answer / guest

Answer: B

Router(config)#boot system ?

WORD TFTP filename or URL

flash Boot from flash memory

mop Boot from a Decnet MOP server

rcp Boot from a server via rcp

rom Boot from rom

tftp Boot from a tftp server

Which of the following is an example of the Datalink Layer? A.) LLC B.) TCP C.) SQL D.) IPX E.) Token Ring F.) MAC

2 Answers  

---

You have two Cisco routers setup back-to-back in a lab using DTE/DCE cables. To which router would you add the clockrate command? A.) The serial port on the DCE router B.) The Ethernet port on the DTE router C.) The Ethernet port on the DCE router D.) The serial port on the DTE router

2 Answers  

---

Identify the command to configure ALL the default VTY ports? A.) Router(config)# line vty 0 4 B.) Router# line vty 0 4 C.) Router(config)# line vty D.) Router(config)# line vty 0

2 Answers   Accel, CMS,

---

You are logged into a router, what command would show you the IP addresses of routers connected to you? A. show cdp neighbors detail B. show run C. show neighbors D. show cdp

2 Answers  

---

The Cisco Catalyst 5000 switch supports full duplex. How would you enable it on the second port of the card in slot 1? A.) router(config-if)# duplex full B.) router(config)# duplex full C.) router(config-if)# set port duplex D.) router(config)#port duplex = full E.) router(config-if)# set port 1/2 full

1 Answers  

---

hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku

4 Answers  

---

What is the Difference between Switch and Bridge?

9 Answers  

---

The benefits to segmenting with Bridges are which of the following? A.) Scalability B.) Datagram filtering C.) Manageability D.) Reliability

1 Answers  

---

hi friends i am jitendera kumar sinha.i have a question in mind that what is the diffrence between router and l3 switch i serched on google and found that switch L3 is best in lan and router are best in wan and switch are more faster then router.beside that any short of technical diffrence if you body know then plz plz and plz reply. my 2nd question is that why we canot replace router with L3 switches (donot tell that it is costly then router).i want any technical cause. this is 1 am hope in noon when ever i logg again i will find the answer posted by you. thanks onse again plz pzl make reply thanks jitendera kumar sinha jitenerasinha.it@gmail.com

5 Answers  

---

Identify 1 characteristic of RARP? A.) MAC to IP address translation B.) Connectionless delivery of packets C.) Can be used to initiate remote O/S load sequence D.) Generates error and control messages

5 Answers  

---

You have OSPF traffic flooding your network via one of your router interfaces. Write the access list line that will deny all ospf traffic. Don't worry about the other lines of the access list.

1 Answers  

---

intial information of packey occur on which layer application sessions physical mine answer physical

1 Answers  

---