I have code and test bench however it is not working porperly. Need help to get it working. module fsm(clock,reset,coin,vend,state,change); \\these are the inputs and the outputs. input clock; input reset; input [2:0]coin; output vend; output [2:0]state; output [2:0]change; \\i need to define the registers as change,coin and vend reg vend; reg [2:0]change; wire [2:0]coin; \\my coins are declared as parameters to make reading better. parameter [2:0]NICKEL=3’b001; parameter [2:0]DIME=3’b010; parameter [2:0]NICKEL_DIME=3’b011; parameter [2:0]DIME_DIME=3’b100; parameter [2:0]QUARTER=3’b101; \\MY STATES ARE ALSO PARAMETERS . I DONT WANT TO MAKE YOU READ \\IN MACHINE LANGUAGE parameter [2:0]IDLE=3’b000; parameter [2:0]FIVE=3’b001; parameter [2:0]TEN=3’b010; parameter [2:0]FIFTEEN=3’b011; parameter [2:0]TWENTY=3’b100; parameter [2:0]TWENTYFIVE=3’b101; \\AS ALWAYS THE STATES ARE DEFINED AS REG reg [2:0]state,next_state; \\MY MACHINE WORKS ON STATE AND COIN always @(state or coin) begin next_state=0; \\VERYFIRST NEXT STATE IS GIVEN ZERO case(state) IDLE: case(coin) \\THIS IS THE IDLE STATE NICKEL: next_state=FIVE; DIME: next_state=TEN; QUARTER: next_state=TWENTYFIVE; default: next_state=IDLE; endcase FIVE: case(coin) \\THIS IS THE SECOND STATE NICKEL: next_state=TEN; DIME: next_state=FIFTEEN; QUARTER: next_state=TWENTYFIVE; //change=NICKEL default: next_state=FIVE; endcase TEN: case(coin) \\THIS IS THE THIRD STATE NICKEL: next_state=FIFTEEN; DIME: next_state=TWENTY; QUARTER: next_state=TWENTYFIVE; //change=DIME default: next_state=TEN; endcase FIFTEEN: case(coin) \\THIS IS THE FOURTH STATE NICKEL: next_state=TWENTY; DIME: next_state=TWENTYFIVE; QUARTER: next_state=TWENTYFIVE; //change==NICKEL_DIME default: next_state=FIFTEEN; endcase TWENTY: case(coin) \\THIS IS THE FIFTH STATE NICKEL: next_state=TWENTYFIVE; DIME: next_state=TWENTYFIVE; //change=NICKEL QUARTER: next_state=TWENTYFIVE; //change==DIME_DIME default: next_state=TWENTY; endcase TWENTYFIVE: next_state=IDLE; \\THE NEXT STATE HERE IS THE RESET default : next_state=IDLE; endcase end always @(clock) begin \\WHENEVER I GIVE A RESET I HAVE TO MAKE THE STATE TO IDLE AND VEND TO 1 if(reset) begin state <= IDLE; vend <= 1’b0; // change <= 3’b000; end \\THE CHANGE ALSO HAS TO BECOME NONE else state <= next_state; case (state) \\HERE WE DECIDE THE NEXT STATE \\ALL THE STATES ARE DEFINED HERE AND THE OUTPUT IS ALSO GIVEN IDLE: begin vend <= 1’b0; change <=3’d0; end FIVE: begin vend <= 1’b0; if (coin==QUARTER) change <=NICKEL; else change <=3’d0; TEN: begin vend <= 1’b0; if (coin==QUARTER) change <=DIME; else change <= 3’d0; FIFTEEN : begin vend <= 1’b0; if (coin==QUARTER) change <=NICKEL_DIME; else change TWENTY : begin vend <= 1’b0; if (coin==DIME) change <=NICKEL; else if (coin==QUARTER) TWENTYFIVE : begin vend <= 1’b1; change <=3’d0; end default: state <= IDLE; endcase end endmodule module test; \\THE INPUT IN THE FSM MODULE ARE REG HERE reg clock,reset; reg [2:0]coin; \\THE OUTPUT IN THE FSM MODULE ARE WIRES HERE wire vend; wire [2:0]state; wire [2:0]change; \\THE PARAMETERS AGAIN FOR THE COIN AND STATE parameter [2:0]IDLE=3’b000; parameter [2:0]FIVE=3’b001; parameter [2:0]TEN=3’b010; parameter [2:0]FIFTEEN=3’b011; parameter [2:0]TWENTY=3’b100; parameter [2:0]TWENTYFIVE=3’b101; parameter [2:0]NICKEL=3’b001; parameter [2:0]DIME=3’b010; parameter [2:0]NICKEL_DIME=3’b011; parameter [2:0]DIME_DIME=3’b100; parameter [2:0]QUARTER=3’b101; \\I MONITOR THE TIME,DRINK,RESET,CLOCK,STATE AND CHANGE FOR CHANGES. initial begin $display("Time\tcoin\tdrink\treset\tclock\tstate\tchange"); $monitor("%g\t%b\t%b\t%b\t%b\t%d\t% d",$time,coin,vend,reset,clock,state,change); \\NEW FEATURE: MY MACHINE HAS THE FACILITY TO DUMP VARIABLES SO THAT \\ I CAN VIEW THEM USING A VCD VIEWER. $dumpvars; $dumpfile("file.vcd"); // Dump output file. \\THIS IS WHERE THE COINS ARE ADDED. clock=0; reset=1; \\FIRST LETS RESET THE MACHINE #2 reset=0; coin=NICKEL; \\CHECK FOR STATE 1 #2 reset=1; coin=2’b00; #2 reset=0; coin=DIME; \\RESET AGAIN AND CHECK FOR STATE 2 #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 reset=1; coin=2’b00; #2 reset=0; \\RESET AGAIN AND CHECK FOR STATE 5 AND SO ON coin=NICKEL; #2 coin=DIME; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=DIME; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=NICKEL; #2 coin=DIME; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=NICKEL; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 reset=0; coin=NICKEL; #2 coin=QUARTER; #2 reset=1; coin=2’b00; #2 $finish; end \\THE CLOCK NEEDS TO TICK EVERY 2 TIME UNIT always #1 clock=~clock; //always @(state) // coin=!coin; initial begin if (reset) coin=2’b00; end \\THIS IS WHERE I INSTANTIATE THE MACHINE fsm inst1(clock,reset,coin,vend,state,change); endmodule

3790

Define what the sop does with the help of an example.

922

What is an interrupt? List various types of interrupts available in 8051 microcontroller?

1092

What is function of ale in 8085 microprocessor?

1007

In 8085 name the 16 bit registers?

1252

Which is non maskable interrupt for 8085?

1017

Define word?

1042

Do the interrupts of 8085 have priority?

981

Explain all the addressing modes of the 8085 with the help of examples.

1017

How is EPROM generally erased

1065

Name 5 different addressing modes?

1027

Why subroutine used in programs?

1105

State the total number of pins in the 8085 microprocessor?

904

Which interrupt is not level-sensitive in 8085?

1043

What is fetch and execute cycle?

1112