As per the Indian Protocol, who among the following ranks highest in the order of precedence ? (a) Deputy Prime Minister (b) Former President (c) Government of a State within his State (d) Speaker of Lok Sabha
4 22001Who among the following was the Constitutional adviser to the Constituent Assembly of India? (a) M. C. Setalvad (b) K. M. Munshi (c) Jawaharlal Nehru (d) B. N. Rau
12 30298Where was the first Municipal Corporation in India set up? (a) Bombay (b) Calcutta (c) Delhi (d) Madras
35 96188In October 2004, where did the Prime Minister of India inagurate the Prototype Fast Breeder Reactor ? (a) Ahmedabad (b) Kalpakkam (c) Thiruvananthapuram (d) Trombay
1 4239Which among the following National Highways of India is the longest ? (a) NH 1 (b) NH 2 (c) NH 3 (d) NH 4
9 14971What is the correct chronological order of the dynasties in which they invaded India ? 1.Huns 2. Kushanas 3. Aryans 4. Greeks (a) 4, 3, 2, 1 (b) 3, 4, 2, 1 (c) 4, 2, 3, 1 (d) 3, 4, 1, 2
5 14719What is the most common salt in sea water ? (A) Sodium Chloride (B) Potassium Chloride (C) Calcium Carbonate (D) Magnesium Sulphate
1 22778For getting instant energy, an athlete should take: (A) Carbohydrates (B) Proteins (C) Vitamins (D) Chewing-gum
4 21494Perform the following tasks using MS-EXCEL: FUEL ESTIMATES COMPUTATIONS: This project is to compute the fuel needed for two types of airplanes, and the cost of the fuel. You must do all computations using formula, and do a chart. Use Page Setup to make the left margin 0.5 and the right margin 0.5 also. Put your name in the Title line, after "Fuel Estimates". Note the following: ? Col. D - H: You must enter correct formulas under Columns D through H (Flying Fuel, Reserve Fuel, Holding Fuel, Total Fuel Needed and Estimated Fuel Cost)!! Read and compute carefully! ? Cells C12, C13, C14, H13 or H14: When you use these cells in a formula, you must make them absolute cell references (F4 key after your type the cell reference, or enter the $ sign manually) ? Graph/Chart: Select cells A3:B8 (Plane and Flight). Hold down the "Control" key and select D3:D8. Hold down the "Control" key and select G3:G8. Create a chart (Insert- Chart, Finish) and position it in a pleasing way under the data for the flight. Print it on one sheet, in landscape mode. ? Print again, but with Formulae: There are two ways to show formulas: 1) Enter Control+` (the key with the ~ at the top left) or 2) Tools-Options, and under "Window Options" put a check mark beside "Formulas", then close the window.
4 13193Which among the following National Highways of India is the longest? 1 NH 1 2 NH 2 3 NH 3 4 NH 4
14 22242Which of the following teams won the First One-day Cricket World Cup held in 1975? 1 England 2 Australia 3 West Indies 4 Pakistan
2 4812Who constructed a famous rockcut Kailas temple at Ellora? (a) Amoghavarsha (b) Krishna I (Successor of Dantidurga) (c) Dantidurga (d) None
1 4993Post New Ignou Interview Questions
What is the difference between filters and interceptors ?
In PFI plant one stage capacitor connection is directly connected(with out megnetic contact controll). but why?
How can i get GR form (GR No.) for Exports ? please give me a link of website with steps ?
Please inform me about the openings of networking field at Kolkata.Is there any interview recently?
pls, send me jindal steels & power aptitude ques
Pls mail me utility & Dg related question with answer
What are the advantages of low-power AI models?
How can you identify the browser and its information using QTP script?
hi friends i m from electrical branch and seeking for tech. + apti. both papers of hpcl plz get it available as soon as possible
If we write the script for login page and click on submit boutton then it opens order page...How we can validate that opened page is wether orderpage or not?
what is the use of schema in biztalk and why we use schema?
one time reffer ur books/(if ur technical students)
What is the difference between business requirement document and use case document.
why do u want to skip from commerce to hr?
Hoew to represent unilateral tolerance, as Bilateral tolerance in engg drawing...? Example: 1.295 +0.000 and -0.10, as unitolerance, write the value in bilateral tolerance?