Interested to Buy Any Domain ? << Click Here >> for more details...
WHAT IS THE SIGNIFICANCE OF VECTOR GROUPS IN TRANSFORMER?
WHAT WILL BE EFFECT WHEN PHASE DISPLACEMENT CHANGES IN
TRANSFORMER?
- 5 Answers
- 25877 Views
- ABB, Nissi Engineering Solution, NSL Sugars, I also Faced
- E-Mail Answers
Answer Posted / sunil ulange hit nidasoshi
Vector Groups are made especially to make out difference in
the connections. The connection can be delta(D) or star(Y)
The primary winding connection always denoted by Capital
Letter (D), and secondary winding connection always denoted
as small letter (y), and neutral n
The number after that indicates the phase difference
between the primary and the secondary voltage.
e.g.-> DYn11 means transformer is star connected with
secondary voltage leading the delta connected primary
voltage by 30 degrees.
normally distribution transformers are have Dyn11 connection
because secondary of transformer are connected to at user
end means motors,inductive load etc,
These loads always havelagging Power factor thatswhy Dyn11
connected transformer means secondary volatage leads by
primry voltage by 30 degrees, hence Power factor maintened
constant.
In Clock 11 indicates angle between 12 & 11 is 30 degrees
i.e. 360/12=30 degree
Sunil ulange
Application Engineer
Southern power equpment Limited bangalore
any Questions @ sunil_031@yahoo.com
| Is This Answer Correct ? | 16 Yes | 11 No |
Post New Answer View All Answers
how to calculate kvar in Akiva
either water sensor or flow meter,how we observe the water level, f any other equipment are in market ?
what happen if drive input fail momentry at 48.5 HZ frequency?
i have a 4 Mva transformer 34.5 kv / 480-277 v and i used 2 parallel 3200 amp bus duct for the secondary feeder using 3 ply of bus bar ( 3/8" x 5" ) as a common where the flexible link terminated and 6300 amps breaker for the main, the lower bus duct reaches 70 degrees and the upper bus duct reaches 55 degrees when i used thermal scanner. why the temperature is not balance when the load reaches 3600 amps.
What facility we get after CT secondary earthing and how?
How to prepare electrical preventive maintenance plan & shedule of machine tools in manufacturing unit.
Use of switch mode power converter in real-time basis?
I have a small system with two motors that are running on 380 vac, 60 hz. These motors are expensive and I usally get them from Brazil. I am adding another motor to the system, but I want to purchase a 480 vac, 60 hz motor to use. It will be on a VFD that is rated fro 380 thru 480. Is this posible and will I have to use a larger motor and derate it?
What is a DC series motor?
can i use 2000/5A Clamp meter to measure HT cable
why wire sizes are 3/29 or 7/29 and why not wire sizes are 2/29 or 6/29?
i want wipro vlsi placement pattern please send me
When we use air circuit breaker, it has O/L protection ,time delay SC protection, Instataneous SC protection & ground fault protection. They all have some setting range. But what is the suitable/allowable setting for the above protection which will be safe for the equipment? For example-O/L protection setting have a range of (0.4,0.45,0.5,0.55,0.6,0.65,0.7,0.8,0.9,1.0)xIn Time delay SC protection have a range of (1.25,1.5,2,3,4,6,8,10,12)xIn Time delay setting is 0.02,0.1,0.2,0.3,0.4 Instataneous setting is fixed to 20xIn Gound fault setting is given 100A,300A,600A,900A,1200A This setting are for 2500A ACB. So what will be the basic allowable setting for the above protection? is there any formulae to calculate this<
how to calculate the capacitor to maintain power factor?
Why do we use copper cable for HT Supply and why not Aluminium?
