Answer / jitendera sinha

ok here is the answer

befor assing ip address you have to determine that what
class of ip you are going to give to your pc

for classs mask
A 255.0.0.0

B 255.255.0.0

c 255.255.255.0

here i assumed that you know about ip address classes and
its range


now how to assign ip address to your pc

go to

control panel---------click on network connection------
rightclick on you lanconection-----------go to properties---
--------go to tcp(last one)--------click on propreties tab--
---------------- assighn ip address(manualy)-----mask will
come atomatclay-------------defaultgateway should be used
and depedet upon your swtic/firwall/router conf.commenly we
use x.x.x.1 herer x is you ip claxx digit

if you donot know any thing abou default gate way
click on atomatic ip address button and dns server ---------
--------------click on ok--------------------click on close

thats it


my hooby is providing answer here so plz plz plase miore
prob

Answer / jm

control panel - network - network devices - properties of nic
- assign ip add and click OK

Given the following output, how can we close Telnet session 2? (Choose two) CCNA2620#show sessions Conn Host Address Idle Conn Name 1 131.108.100.152 131.108.100.152 0 131.108.100.152 *2 126.102.57.63 126.102.57.63 0 126.102.57.63 ❍ A. Press the Enter key and enter exit. ❍ B. Enter disconnect 2. ❍ C. Press the Enter key and enter disconnect 2. ❍ D. Enter close 2.

1 Answers  

---

What are the netbios and netbeui?

0 Answers  

---

Which technology is used by Catalyst switches to resolve topology loops and ensure data flows properly through a single network path? A. virtual LANS (VLANS) B. frame filtering C. cut-through switching D. spanning-tree protocol

2 Answers  

---

what are the port numbers for DNS,FTP,TELNET,SMTP,NNTP

5 Answers   Airtel, Walton Group,

---

what is the difference between 1 router and switch 2 router and hub 3 hub and switch 4 bridge and switch

1 Answers   Hathway,

---

please name some routed protocol.

1 Answers  

---

Identify the default IPX serial encapsulation? A.) Novell-Ether B.) SDLC C.) SNAP D.) HDLC

1 Answers  

---

Which of the following is not a characteristic of link-state routing protocols? ❍ A. VLSM support ❍ B. Route summarization at any bit level ❍ C. Full routing updates at regular intervals ❍ D. Discontiguous network support

2 Answers  

---

Which ISDN specification deals with call Setup and Teardown? A.) Q-Series B.) J-Series C.) I- Series D.) C- Series E.) F-Series

1 Answers  

---

Can anybody tell me how to configure a cisco router?

2 Answers  

---

here is your question sahin Hi Jitendera, If i m not wrong, then in EIGRP, Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0. This is default setting for EIGRP. I knew about it from ICND 2 cisco press book. Three more questions - a) If we change the K value (I mean metric weight)on a router what will happen??? b) When redistribution is necessary in EIGRP. Is there any condition for that??? c) What is reference bandwidth for metric calculation in EIGRP. As we know, in OSPF, on a CISCO router reference bandwidth is 10Mbps.

3 Answers  

---

Identify the command that saves the configuration stored in RAM to NVRAM? A.) copy running-config startup-config B.) copy tftp running-config C.) copy startup running D.) copy active to backup

2 Answers  

---