Hello Every one. Actually its my first time to using this
site and first time to posting a question. Actually i need
to know about CCNA Exam. Please can any one tell me about
the Exam style and any recommendation for study? Best
Regards to all the Friends
Buddy, Nice to see here...!!! First of all u need to have
damn dedication to pass any cisco exam.
First of all, go through Cisco press book for CCNA. watch
out all multiple question of that books.
Be very proficient in subnetting (FLSM & VLSM, Protocol
concept (RIP, RIPv2, EIGRP & OSPF single area only),
configuration & also troubleshooting.
Be good knowledge of every sh commands & output of those
command.
Be good concept on switching, VTP, VLAN, Trunking, not only
configuration but also troubleshooting.
WAN technology (ISDN, Frame Relay) PPP, HDLC, CHAP PAP
configuration & troubleshooting.
So my recommandation is spend more & more time spend with
books. CCNA study guide, Cisco press book.
Last advice, go through Dumps & write the exam. Don't use
cheat code... after all u gonna cheat urself.
All the very best..!!!
Is This Answer Correct ? | 2 Yes | 0 No |
Identify the command that will display the RIP routes entering and leaving the router? A.) Router(config)# debug ip rip B.) Route# debug ip rip C.) Router>debug ip rip D.) Router# debug rip routes
Mention what is the difference between the switch, hub, and router?
Do we subletting of ip?
What parameter is used with statically assigned routers to tell packets which interface to use to reach a distant network? A.) Mask B.) Subnet C.) Default gateway D.) Interface
Identify the 3 characteristics of IGRP? A.) Uses hop count as a metric B.) Supports multiple unequal paths C.) Administrative distance is 100 D.) Configured with an Automous system number E.) Link state
Which processes does TCP, but not UDP, use? A. Windowing B. Acknowledgements C. Source Port D. Destination Port
Identify the correct IGRP configuration? A.) Router# router igrp 100 Router# network 10.0.0.0 B.) Router(config)#router igrp 100 Router(config-router)#network 10.0.0.0 C.) Router(config)# router igrp Router(config-router)# network 10.0.0.0
What are hold-downs used for? A.) To prevent regular update messages from reinstating a route that has come back up B.) Information received on an interface cannot be sent back out the same interface C.) To prevent regular update messages from reinstating a route that has gone down D.) To hold the routing table from being sent to another router
wat is last assignable host address in 209.165.201.0/27 network?
You have a Class B network address divided into 30 subnets. You will add 25 new subnets within the next year. You need 600 host IDs for each subnet. Which subnet mask should you use? A.) 255.254.0.0 B.) 255.192.0.0 C.) 255.255.252.0 D.) 255.255.248 0
When a Distance Vector routing protocol detects that a connected network has gone down, it sends out a special routing update packet, telling all directly connected routers that the distance to the dead network is infinity. This is an example of which routing technology? A.) ICMP. B.) Only Link State routing protocols have this intelligence. C.) Triggered updates. D.) Garrison-4. E.) Split Horizon. F.) Poison Reverse.
Hi Guys i hv one confusion. Need u peoples help. In EIGRP, maximum hop count is up to 255. By default only 100. Now question is - a) Suppose i hv a network consist of 115 routers & EIGRP routing protocol is configured. By default hop count is 100, so is there any manual configuration necessary for hop count ya router will automatically detect the hop count & will update the hop count accordingly..????? b) In EIGRP, Bandwidth & Delay is used to calculate metric. For this Metric weight is set to K1(Bandwidth)=1, K2(Delay)=0, K3(Reliability)=1, K4(Load)=0, K5(MTU)=0 Now i want, Bandwidth & Load is used to calculate metric. For that wat i hv to configure & wat wub the metric weights. Cud anyone explain it plzzzz..!!!!