thnx Jitender singh...as u told to install a stp in switches
and problem vil b get solved...i wanna kno how to install
stp in switches??
plz tel me detailled steps...
thanx for ur answer.



thnx Jitender singh...as u told to install a stp in switches and problem vil b get solved...i wanna..

Answer / jitendera sinha

actauly i have the certfications of ccna not ccnap
confrigring stp at switches is not in the sylb of ccna so i
donot know exatly.but i will naswer it after the study of
that.but as far as my knowledge is consern stp is
implemented on cisco switches by default
thanks

Is This Answer Correct ?    0 Yes 1 No

Post New Answer

More CCNA Interview Questions

Define Poison Reverse? A.) To prevent regular update messages from reinstating a route that has gone down B.) Packets sent out that are not destined for a network go to the default network C.) Information received on an interface cannot be sent back out the same interface D.) When a network goes down, that network is advertised with an infinite metric

1 Answers  


what is the subnet for the host ip address 172.16.210.0/22

8 Answers   IBM, Microland,


Which table find best path?

0 Answers  


What is the standard ISDN term for a non-native analog telephone? A.) TE1 B.) TA C.) LE D.) TE2 E.) ET

1 Answers   DELL,


What is Phase od VPN in site to site and what information you will require to configure a SITE to SITE VPN

0 Answers   Infosys,






Which two statements about IP RIP are true? (Choose two) A. It limits hop counts to 31 B. It is a link state routing protocol C. It uses autonomous system numbers D. It is capable of load sharing over multiple paths E. It uses bandwidth as the metric for path selection F. It broadcasts updates every 30 seconds by default

1 Answers  


Which is true regarding half duplex Ethernet operation? A.) Half Duplex ethernet technology provides a transmit circuit connection wired directly to the receiver circuit at the other end B.) Half duplex transmission between stations is achieved by using point to multipoint Ethernet and Fast Ethernet C.) With Half Duplex transmission logically circuits feed into a single cable creating a situation similar to a one way bridge D.) Half Duplex transmission between stations is achieved using Point to Point Ethernet & Fast Ethernet

2 Answers  


Tell me how many hop counts are by default and how much you can increase in eigrp protocol?

0 Answers  


Identify the true statements about the following access list: Access-list 101 deny tcp 192.10.172.0 0.0.0.255 any eq 23 Access-list 101 permit ip any any A.) This access list prevents the host 192.10.172.0 from telneting B.) This access list prevents any telnet traffic from subnet 192.10.172.0/24 C.) This access list filters some telnet access D.) This access list denies any telnet traffic to subnet 192.10.172.0/24 E.) This access list is invalid F.) The netmask on the this access list is reversed

1 Answers  


If a frame is received at a switch and only the destination hardware address is read before the frame is forwarded, what type of switching method is this? A.) Store-and-drop B.) Latency C.) Store-and-forward D.) Cut-through

1 Answers  


What should be the first command to create an access-list that prevents all users on subnetwork 10.10.128.0, using subnet mask 255.255.192.0, from being able to telnet anywhere? A.) access-list 101 deny tcp 10.10.128.0 0.0.63.255 any eq telnet B.) access-list 101 deny tcp 10.10.128.0 255.255.0.0 any eq telnet C.) access-list 101 deny tcp 10.10.128.0 255.255.192.0 any eq telnet D.) access-list 101 deny tcp 10.10.128.0 0.0.192.255 any eq telnet E.) access-list 101 deny tcp 10.10.128.0 0.0.128.255 any eq telnet F.) access-list 101 deny tcp 10.10.128.0 0.0.127.255 any eq telnet

3 Answers  


What is the usage of service password encryption?

0 Answers  


Categories