Based upon the exhibit, create a static route to 172.16.10.0 on Router A A.) Router# ip route 172.16.10.0 255.255.255.0 10.1.0.2 B.) Router(config)# ip static route 172.16.10.0 255.255.255.0 10.1.0.2 C.) Router(config)# ip route 172.16.10.0 10.1.0.2 D.) Router(config)# ip route 172.16.10.0 255.255.255.0 10.1.0.2

1 Answers  

---

What command displays the OSPF Process ID, Router ID, Address summarizations, Routing Networks, and passive interfaces configured on a router?

1 Answers  

---

Which of the following will show an extended access list 150? A.) sh access-list 150 B.) sh ip int C.) sh ip access-list D.) sh access-list 150 extended

2 Answers  

---

Identify the type of routing protocol that exchanges entire routing tables at regular intervals? A.) Link state B.) Interior gateway protocols C.) Appletalk routing D.) Distance vector

2 Answers  

---

What are the advantages of a layered model in the networking industry?

0 Answers  

---

Can you explain different components in PKI?

0 Answers   CCIE,

---

What are the steps of conversion for data encapsulation?

0 Answers  

---

What is the subnet? Why is it used?

0 Answers  

---

hello friends im murtaza frm indore... and my question is that im doing hardware engenering and networking and im intrested in make a good career in networking so can you suggest.. which institiue is good for me...plzzz replyy im waiting...

1 Answers  

---

hi i am facing one problem.ptoblem is like that i am getting output error on mine router ethernet interfae here is the cisco#show interface e0 Ethernet0 is up, line protocol is up Hardware is QUICC Ethernet, address is 0030.802d.2a17 (bia 0030.802d.2a17) Internet address is 202.122.20.225/28 MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 05:55:07 Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 10000 bits/sec, 11 packets/sec 5 minute output rate 29000 bits/sec, 11 packets/sec 1515202 packets input, 359100396 bytes, 1 no buffer Received 6 broadcasts, 0 runts, 0 giants, 1 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected 1584394 packets output, 1623395338 bytes, 0 underruns 1820 output errors, 26732 collisions, 0 interface resets 0 babbles, 0 late collision, 9698 deferred 18 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out output cisco# what is the reason how to solve this please tell me i am using cisco asa 5520 behid mine internet router and no error on the asa inside interface

2 Answers  

---

You have two Cisco routers setup back-to-back in a lab using DTE/DCE cables. To which router would you add the clockrate command? A.) The serial port on the DCE router B.) The Ethernet port on the DTE router C.) The Ethernet port on the DCE router D.) The serial port on the DTE router

2 Answers  

---

What cable called v.35?

0 Answers  

---