What are three LAPB features supported by SDLC?
A. Frame types
B. Frame format
C. Field functions
D. ABM
- 1 Answers
- 4104 Views
- I also Faced
- E-Mail Answers
Answer / guest
Answer: A, B, and C
Three LAPB features supported by SDLC are frame types, frame
format, and field functions. These are shared by both HDLC
and SDLC.
| Is This Answer Correct ? | 2 Yes | 0 No |
What is the first step in diagramming packet flow for the terminals within a network? A. Identify the end user nodes of all the terminals B. Figure out the speed of all the servers C. Find out where all the routers are located D. Find out where all the switched are located
What happens to performance if the maximum MTU (Maximum Transmission Unit) size is used? A. Performance increases B. Performance decreases C. Performance stays the same D. Performance has nothing to do with the MTU
What address is 12 hexadecimal, resides in the Data-Link layer, and is burned in the ROM by the manufacturer.
What happens when the hold-down timer expires? A. Routes are flushed from the routing table after the flush timer expires B. Routes are flushed from the routing table immediately C. Routes are never flushed D. A triggered update will reset the hold-down timer
Which of the following are true regarding switched virtual circuits (SVCs) and permanent virtual circuits (PVCs)? Choose two. A. SVCs and PVCs can use the same circuit. B. PVCs are permanently established virtual circuits. C. SVCs and PVCs terminate the circuit when data transmission is complete. D. SVCs are virtual circuits that are dynamically established on demand and terminated when data transmission is complete.
What is not a function of the distribution layer? A. Routing between VLANs B. Implement tools such as access lists, packet filtering, and queuing C. Implement security and network policies D. Provide workgroup/user access to the network
What set of Frame Relay enhancements offer extensions for managing complex internetworks? A. CMT B. SNMP C. LMI D. RMON
Which of the following does not specify an application requirement that affects your network design? A. The number of users B. The peak hours that the applications are used C. The types of applications used D. Security risks
How many networks will be advertised using route summarization within an OSPF network if you are given the following networks? 192.108.168.0 192.108.169.0 192.108.170.0 192.108.171.0 192.108.172.0 192.108.173.0 192.108.174.0 192.108.175.0 A. 1 B. 2 C. 3 D. 4 E. 5
Traffic Shaping does which one of the following? A. Eliminates bottlenecks by throttling back traffic volume at the source or outbound end B. Reduces the frame size so bandwidth is better utilized C. It increases source traffic to a configured bit rate D. Allows you to control hubs and repeaters
Which two of the following describe ASN.1 (Abstract Syntax Notation One)? A. It is an abstract routing protocol that is not used very often. B. It is an OSI language for describing data types independent of particular computer structures and representation techniques. C. Consists of only one basic routing algorithm. D. Uses BER (Basic Encoding Rules).
How can I release the restriction of CISCO2811C/K9? 10M optical fiber, Speed limit of 125kb / s, made by last network administrator, how can I release the restriction? Please tell me the detail, thanks! Cisco configuration： CISCO2811C/K9 ! ! ! ! ! ! ! interface FastEthernet0/0 description WANpork ip address x.x.x.x 255.255.255.248 ip access-group 110 in no ip proxy-arp ip verify unicast reverse-path ip nat outside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1 description LANpork ip address 192.168.x.x 255.255.255.0 ip access-group 101 in no ip proxy-arp ip verify unicast reverse-path ip nat inside ip virtual-reassembly rate-limit output 1000000 1000000 1000000 conform-action transmit exceed-action drop duplex auto speed auto !
CCNA 
