Interested to Buy Any Domain ? << Click Here >> for more details...
Which layer of the 7 layer model provides services to the
Application
layer over the Session layer connection?
A.) Transport
B.) Application
C.) Session
D.) Network
E.) Datalink
F.) Presentation
- 2 Answers
- 5721 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Tell me which cable called roll-over?
Hi Guys I am facing one problem while configuring PAP over Point to Point links. Configuration scenario is like this. ROUTER 1: (Hostname – R1) R1(config)#username R2 password CCNA2 R1(config)#interface serial 1/1 R1(config-if)ip address 10.0.0.1 255.0.0.0 R1(config-if)#lock rate 64000 R1(config-if)#encapsulation ppp R1(config-if)#ppp authentication pap R1(config-if)#ppp pap sent –username R1 password CCNA1 R1(config-if)#no shutdown ROUTER 2: (Hostname – R2) R2(config)#usename R1 password CCNA1 R2(config)#interface serial 1/1 R2(config-if)#ip address 10.0.0.2 255.0.0.0 R2(config-if)#encapsulation ppp R2(config-if)# ppp authentication pap R2(config-if)# ppp pap sent –username R2 password CCNA2 R2(config-if)#no shutdown Now problem is that, after configure the command “ppp authentication pap” the “Line protocol” status goes down on each router. But when I disable this command using “no ppp authentication pap”, the “Line Protocol” status goes up. What could be the problem, can anyone explain it plzzz….!!! Thanks in Advance…!! Shahin..
how many pass word you can configure on cisco 2500 router
what is ACLs? what is the reasons to create ACLs?
Which 3 statements describe default encapsulation and LMI type configuration? A.) There are only four encapsulations and 3 LMI type options B.) The LMI type config term options C.) In release 11.3 the LMI type is autosensed D.) The default LMI is Cisco E.) IETF encap must be configured unless the connecting routers are both cisco
Can anyone explain in details port fast, uplink fast & backbone fast features introduced by CISCO (The GOD FATHER of NETWORKING.... Hehehehehe).
Identify the switching method that examines the destination MAC address as the frame is being received then begins forwarding the frame prior to receiving the entire frame? A.) Fragment-free B.) Store and Forward C.) Cut-through D.) Fast forward
If you have configured IPX on a Serial interface, which command would display the IPX network and node address on the Serial 1 interface? A.) show interface B.) show ipx s1 C.) show interface s1 D.) show ipx int serial 1 E.) show ipx int brief
Identify 3 methods used to prevent routing loops? A.) Split horizon B.) Holddown timers C.) Poison reverse D.) SPF algorithm E.) LSP's
You have typed "ping" 172.16.101.1 and get the following display: Type escape sequence to abort. Sending 5, 100-byte ICMP Echoes to 172.16.101.1, timeout is 2 seconds: .!!!! What does the "." signify? A. That one message timed out. B. That all messages were successful. C. That one message was successful. D. That one message completed in under the allotted timeframe.
Given the command 'cl?', what will it display? A.) Syntax of the 'clock' command B.) Syntax of the 'clear' command C.) All commands that begin with 'cl' D.) All commands that begin with 'c'
Given the configuration example: interface ethernet0 ipx network 4a ipx access-group 800 out interface ethernet1 ipx network 3d interface ethernet2 ipx network tc access-list 800 permit 3d 4a Which action result from implementing this configuration? a-Traffic from network 3d for network 4a will be forwarded out e0 b-IPX network 5c will not receive any traffic c-Traffic from network 3d, destined for network 4a, will be forwarded out e2 d-Traffic from network 3d for network 3d will be forwarded out e0
CCNA 
