1. Categories >> Certifications >> Cisco Certifications >> CCNA
  2. Suggest New Category

Which protocol is used for booting diskless workstations?

A.) IP

B.) ARP

C.) RARP

D.) TCP

E.) SNMP

Question Posted / guest

Answers were Sorted based on User's Feedback



Which protocol is used for booting diskless workstations? A.) IP B.) ARP C.) RARP D.) TC..

Answer / santosh kumar

answer to this question is "c" ie rarp in place of this it
may be bootp or dhcp since all these do same work.... its
work is to get physical to logical address maping....
santosh kumar ... jmi final yr,,

Is This Answer Correct ?    5 Yes 0 No

Which protocol is used for booting diskless workstations? A.) IP B.) ARP C.) RARP D.) TC..

Answer / guest

Answer: C

Is This Answer Correct ?    4 Yes 2 No

Which protocol is used for booting diskless workstations? A.) IP B.) ARP C.) RARP D.) TC..

Answer / saurabh

answer for this que is bootp. jmi comp engg final year 2011-2015 batch

Is This Answer Correct ?    3 Yes 1 No

Post New Answer

More CCNA Interview Questions

What is poe (power over ethernet)?

0 Answers  

Given the global configuration commands: 'banner motd #' 'Hello #' When would the message be displayed? A.) The message of the day banner shows up before login. B.) The message of the day banner shows up during logoff. C.) These commands are not the right syntax for MOTD. D.) Message of the day banners are displayed upon entering global config mode. E.) Message of the day banners are not possible. F.) The message of the day would be, 'Hello #'

1 Answers  

Explain what is eigrp?

0 Answers  

what is the difference between hdlc and ppp protocol

7 Answers   ASD Lab, HCL,

Which type of Ethernet framing is used for TCP/IP and DECnet? A. Ethernet 802.3 B. Ethernet 802.2 C. Ethernet II D. Ethernet SNAP

1 Answers  




Hi Jitendera, I continuously read your answers which is more knowlegable than books... Q.I am facing some problems in subnetting.can you plzz explain the subnetting process.. will be remain thankful

4 Answers  

How does L2TP process?

0 Answers   CCIE,

What does a Standard IP Access-list use as test criteria? A.) IP source address B.) IP source and destination address, protocol numbers and port numbers C.) IPX source and destination address D.) Source MAC address

2 Answers  

Identify the command to configure the router to boot from an IOS located on a TFTP server? A.) boot system tftp IOS.exe 172.16.5.1 B.) boot system tftp 172.16.5.1 IOS.exe C.) boot system flash tftp 172.16.5.1 D.) boot system IOS.exe 172.16.5.1

1 Answers  

What do the following commands accomplish? access-list 1 deny 172.16.4.0 0.0.0.255 access-list 1 permit any interface ethernet 0 IP access-group 1 out A. This will block traffic from subnet 172.16.4.0 and allow all other traffic. B. This will allow traffic from subnet 172.16.4.0 and block all other traffic. C. All traffic is allowed. D. All traffic is blocked.

1 Answers  

what are the different asymmetric algorithms?

0 Answers   CCIE,

The following commands were entered at the command prompt of a Cisco router. What do they accomplish? access-list 1000 deny 9e.1234.5678.1212 4 access-list 1000 permit -1 interface ethernet 0 ipx network 9e interface ethernet 1 ipx network 4a interface serial 0 ipx network 1 ipx output-sap-filter 1000 A. File server advertisements from server 9e.1234.5678.1212 will not be forwarded on interface S0. B. All other SAP services, other than file server, from any source will be forwarded on S0. C. All other SAP services, other than print server, from any source will be forwarded on S0. D. Print server advertisements from server 9e.1234.5678.1212 will not be forwarded on interface S0.

1 Answers  

For more CCNA Interview Questions Click Here
Categories