What is the default encapsulation and frame type on an Ethernet
interface
when enabling Novell?
A.) SNAP
B.) Ethernet_II
C.) 802.2
D.) 802.3
E.) SAP
F.) Novell-ether
- 2 Answers
- 7613 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
Identify the command that specifies Serial 0 in slot 1? A.) Router(config)# interface serial1/1 B.) Router(config)# interface serial1/0 C.) Router(config)# interface serial0.1 D.) Router(config)# interface serial0/1
Identify the 2 commands to copy a configuration from a TFTP server to RAM? A.) configure network B.) configure overwrite C.) copy backup-config running-config D.) copy tftp running-config
Which IEEE standard is used to define Wi-Fi? A. IEEE 802.3 B. IEEE 802.5 C. IEEE 802.11h D. IEEE 802.11c E. IEEE 802.11
Identify the length of an IPX address and it's components? A.) 80 bits, 48 bits network and 32 bits node B.) 32 bits, 16 bits network and 16 bits node C.) None of the above D.) 80 bits, 32 bits network and 48 bits node
What is the main advantage of using switches?
switch kitne volt per work karta hai. what is frame realy. what is isdn and pri and bri.
What are the things that can be accessed in a CISCO router’s identifying information?
Identify the command to reload the router? A.) Router(config)# reload B.) Router# reset C.) Router# reload D.) Router> reload
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
What is the igp (interior gateway protocol)?
You create the following standard access-list access-list 1 deny 1.1.1.1 access-list 1 deny 2.2.2.2 int e0 ip access-group 1 in Which of the following statements are true, with regard to traffic flowing into E0? A.) This will stop IP packets with a source address of 1.1.1.1 only. B.) This will stop all IP packets. C.) This is an invalid configuration. D.) This will stop no IP packets. E.) This will stop IP packets with a source address of 2.2.2.2 only. F.) This will stop IP packets with a source address of 1.1.1.1 and 2.2.2.2.
Which show command should you use to view Frame Relay Local Management Interface (LMI) Frame statistics? A. show lmi B. show ip route C. show interface D. show statistics E. show frame-relay lmi
CCNA 
