Identify the command mode necessary to enter the standard ping
command?
A.) Router(config)#
B.) Router>
C.) Router(std-ping)#
D.) Router(config-if)#
- 2 Answers
- 4515 Views
- I also Faced
- E-Mail Answers
Answers were Sorted based on User's Feedback
what is used for passive intercae comand mine answer-to prevent to take update from outside
the situation iz like ths -at a specific time in our company the internet connectivity goes off...v hav two networks in our company...but out of it only one link goes down for 5-10 sec...a fastethernet port becomes down for few sec and automatically becomes Up... Is this occures becoz of Power?? If yes thn y the 2nd network is not affected??
What are segments?
hello friend i have answerd more time of your question or doute.now i am seeing towards you for help,plz send the soln before monedya the problem is i have three router r1 and r2 and r3 they are conested in that maneer thai is r1---r2---r3---server | | server bothe server have diffrent ip now i have to implemnt access list on the r3 router in such a way that user from r1 can access only one server while user from r2 can access whole servre i ahve done it but both user of r1 and r2 uses all server i need help please help me this time? i have repalsced my firwall by r3 router so bacicaly i have to implement it on my firewall but you tell me on cisco router please help
Hi Everyone,i have done b.e. and i am CCNA certified, i am searching jobs related to ccna. Although i don't have experience in networking field, i found very difficult to search job(posted my resume in all job portals). I am very much interested to work in networking field, please guide me, my mail id: karnailthakur@gmail.com; Please let me know any company taking ccna freshers(Preferably delhiNCR location). Thanks guys...
What is the icmp protocol?
Which protocol you manually enable route summarization?
What does a metric of 16 hops represent when using RIP? A.) Number of hops to the destination B.) Destination unreachable C.) Number of routers D.) Bandwidth
hi... i am usin packet tracer 5.0.. i hav connect two routers A and B. A has 200.100.25.100 and 1.0.0.1 and router B has 200.100.50.100 and 1.0.0.2... i hav connected 1.0.0.1 and 1.0.0.2... now i want to route 200.100.25.100 and 200.10.50.100 usin rip.. i enable rip in both the routers... but whn i give the command show ip route... i jus get this Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR P - periodic downloaded static route Gateway of last resort is not set A# so can sombody tell me where i hav gone wrong... thanku
What are the 2 functions of the Data Link Mac layer? A.) Handles access to shared media B.) Manages protocol access to the physical network medium C.) Provides SAPs for higher level protocols D.) Allows multiple devices to uniquely identify one another on the data link layer
You have OSPF traffic flooding your network via one of your router interfaces. Write the access list line that will deny all ospf traffic. Don't worry about the other lines of the access list.
Explain the difference between named and extended acl?
CCNA 
