Which service uses telephone control messages and signals
between
the transfer points along the way to the called destination?
A. Signaling System 7 (SS7)
B. Time-division Multiplexing (TDM)
C. X.25
D. Frame relay
Answer / guest
Answer:: A
Signaling System 7 (SS7) uses telephone control messages and
signals
between the transfer points along the way to the called
destination.
Time-division Multiplexing (TDM) has information from
multiple sources
and allocates bandwidth on a single media. Circuit switching
uses
signaling to determine the call route, which is a dedicated
path between
the sender and the receiver. Basic telephone service and
Integrated
Services Digital Network (ISDN) use TDM circuits. X.25 and
Frame Relay
services have information contained in packets or frames to
share
non-dedicated bandwidth. X.25 avoids delays for call setup.
Frame Relay
uses permanent virtual circuits (PVCs).
Is This Answer Correct ? | 0 Yes | 0 No |
How do you depict an IP address?
On which bas ospf take decision?
How do areas benefit a link state inter network?
(1)what is "rtp" and how it work, (2)what is diffrence between igrp and eigrp (3)the slection prcedure of dr and bdr is depend open (4)why frame really is called nbma (5)what is ppp (6) what is diffrence b/w tcp and udp (7) how can we implement ospf protocall on any router (8)whta is as nomber (9)what is AD value (10)what is the broadcast id,n/w id and number of vallid host of the 255.255.255.128/25 195.168.10.10/25 (11) what is stub network (12) what is contigues n/w (13)on which type of router we can implement default routing (14)what is diffrence b/w hub switch;switch router, (15)what is v lan (16)what is the diffrence b/w link sate protocal and distance vector protocall (17)what is synchoransh mode of data transfer and asynchronash mode of data transfer (18) question on lab, belive me frnds there are 20 questions and 5 questions on lab implimentaion.around 1.1/2 hour i was in interview room and after givieng 17 right answera and 4 in lab i got slected try to give answer if any difficulty or any prob plz email me on jitenderasinha.it@gmail.com if any one of you havae boson netsim plz also intimate me
Which command line statement determines the number of seconds a dialup connection can wait without any traffic before the router hangs up? A.) dialler max-time B.) dialler timeout C.) dialer idle-timeout D.) dialer hang-up E.) disconnect-timer
What is the last step in data encapsulation? A.) User information is converted into data. B.) Segments are converted into datagrams and packets. C.) Frames are put into bits. D.) Data is converted into segments. E.) Packets are put into logical frame.
What key do you use to view the last command? A.) Ctrl+X B.) Ctrl+Z C.) Ctrl+E D.) Ctrl+P
Explain the types of communication in ipv6 ?
Identify the command to display the Frame Relay map table? A.) Router# display frame-relay map B.) Router# show frame-relay map C.) Router(setup)# show frame-relay map D.) Router# show map frame-relay
how will configure Nat
In configuring a router, what command must be used if you want to delete the configuration data that is stored in the NVRAM?
The following selections show the command prompt and the configuration of the IP network mask. Which two are correct? A. Router#term IP netmask-format { bitcount | decimal | hexadecimal } B. Router(config-if)#IP netmask-format { bitcount | decimal | hexadecimal } C. Router(config-if)#netmask-format { bitcount | decimal | hexadecimal } D. Router#ip netmask-format { bitcount | decimal | hexadecimal }