How can I make calculation for Install level transmitter
(DP) for open tank and cloes tank?
- 1 Answers
- 3722 Views
- Petrofac, I also Faced
- E-Mail Answers
Answer Posted / mnb
For open tank you just connect HP side to the bottom of the tank and vent LP side to the atmosphere.
Head pressure becomes liquid level .URV=Height*specific gravity (H*SG) and LRV =0.
For closed tank, use dry leg for non condensate liquids and use wet leg for condensate liquids.
Dry leg-connect HP side to bottom and LP side to top of the tank. LRV =0, URV= H*SG.
No need to bother about pressure inside the tank because it acts upon both sides equally.
Wet leg- connect Hp side to lower tapping and LP side to upper tapping and fill the Lp side with process liquid.
LRV=h2*sg
URV= h1*sg-h2*sg.
h1= level of liquid at HP side
h2= level of liquid at LP side.
| Is This Answer Correct ? | 1 Yes | 0 No |
Post New Answer View All Answers
principle of dead weight tester ?
What is the Working principle of Dozing valve?
Good evening all I need a small favour regarding reliance paper i wanna probable sample papers(e&i) of reliance. if any of u have any idea about dis then plz mail me back.i belongs to electronics and instrumentation engg.so i need e&i papers. thanking u....
please send data bank of quetions answers on analytical instrumentation.
DEAR SIR/MADAM MY NAME IS ARKAPROVA BHATTACHARYYA.I AM A FRESHER INSTRUMENTATION ENGINEER.CAN YOU PLEASE SEND SOME QUESTION PAPERS OF GRADUATE ENGINEER TRAINEE EXAM OF DVC(DAMODAR VALLY CORPORATION).MY EMAIL IDs ARE arka_aec@rediffmail.com.
hi i am eswar i want to know the instrumentation interview questations for eil(engineers india ltd) i have applied for engineer post in eil please help in this.my mail id eswar310@gmail.com
use of split range ? where it is used ? in which control loop it is used ?
this site is owned by an nonsense
plz you help about Que paper of mahagenco previous your,any model paper relad to it{maharastra power genration}
hi sir yhis is zahid ali i am preparing for the jspl at oct.4.please send me the recently updated sample paper.
please tell no. & add. of consultancy who recruit me in power plant as instrumen engg. present i m working in power plant as ass.t instrument engg. thanku mahesh 09226562826
A PLC is programmed to drive three motors A, B and C as follows : After running motor A for an hour, motor B should get ON and motor A should get OFF. And after running motor B for an hour, motor C should get ON and motor B should get OFF. And after running motor C for an hour, motor A should get ON and motor C should get OFF. (That is, a cyclic repetition with time period one hour) Now, the second condition is: If any motor gone faulty and is tripped, the consecutive motor should get ON and the faulty (tripped) motor should be eliminated from cyclic repetition. The remaining two motors should bear the cyclic repetition of one hour each. (For healthy motor take logic as high and for tripped motor take logic as low) Now, the third condition is: When motor A load(Amps) exceeds 60% of its rated load, motor B should get ON in parallel to motor A. And when both motors A & B are running in parallel, and if their load exceeds 60% of their rated load, motor C should also start in parallel to A & B. [Here the cyclic repetition is eliminated, until their loads become normal(40%)] [Take logic high(1) for load at 60% and logic low(0) for load at 40%] Now draw a flow chart or a ladder diagram to fulfill the above condition.
hello can yoy pls send me previous papers of jindalpower and steel ltd.....'m from instrumentation..... mani1048@gmail.com
Punj lloyd is coming in our Jadavpur Universtiy campus for campus placement. Please send me some hints about the writtend exam. My email id is subratafriends@gmail.com
Can any body help to get Rsemulator 5000 free from internet if possible then give me any link or any help .
