Answer Posted / senthilnathan.j vizhidiyur

If you are going to test k-type thermocouple at normal room
temp.first you check the resistence of the themocouple using
multimeter.if junction is open then it shows Mohms means the
thermocouple is dead.it will show 0 resistence when it is in
good condition. then you check the milllivolt output by
touching the terminals with correct polarity (For k-type
red-positive; green-negative) using multimeter.at room
temprature the output of thermocouple is 0mV because both
the hot junction and cold junction are in same temprature
say 30deC.
then set the hotbath temp. into 100C and put the T/C inthat
and now check the T/C teminals it should show 4mV because
for K-type For 1degC =0.04mV will rise.It is difficult to
find that much minimum voltage.so that only we are taken the
reading at 100degC. now you are successfully tested the
Thermocouple.

what are procedure of sox-nox calibration

3038

---

What is Cavitation in a control valve?

2126

---

How hart protocol can be connected with control valves?

1106

---

Lux meter is the measuring device to measure the lux level of lighting fixture. in industrial sector two types of lighting fixture is being used as street lighting purpose 1. HPSV (Sodium) and 2. HPMV (Mercury). HPMV having white light which is an combination of red, blue and yellow colour, while HPSV haivng Yellow lighting. in HPSV red & blue colour will be absent. during measurement of the lux level of HPSV and HPMV fixture. 1. Lux meter can measure the actual lux level of both fixture? 2. or it will show false reading for HPSV fixture light as it has only yellow light present. please give me answer

4714

---

How will you test a transistor with a multimeter?

1148

---

how to calculate orifice sizing? and tell me if pipe size bet 50mm t0 200mm then we can use pipe flange??? and above 250mm pipe size should i use D & D/2 Flange? is it right or wrong?

1937

---

What are the materials available to prepare individually for competetive exams in Instrumentation field? Plz reply...

2154

---

TECHNICAL/ARTITUDE

2302

---

hello friends, can you please send me the model paper or question paper to be prepared for hpcl examinations????????? You can mail me at rahim_here@yahoo.com waiting for your reply........... help me .. plz.....

2649

---

I have completed B.E. Instrumentation & control in 2009. i have 3 year industrial job experience in chemical plant.now, I want to join M.E. in external. so, Plese say easiet way and good institute name.

1943

---

kindly sent some demo question and answer

2118

---

Why use ball valves on Gas pipelines instead of gate & or globe valves...means basic diffrence or use of these valves..how designers knows this type of valve with rating is required...

2394

---

Q1: Consider part of a control loop, which excludes the transmitter, consisting of a process, a controller and a control valve which may be represented by two dead times of 0.5 min each and three exponential lags of 0.8 min., 1.0 min. and 1.5 min. respectively. We wish to express this system as an overall first order plus dead time (FOPLD) model ie gain, time constant and process dead time. (We will see later that this is often done, to simplify controller tuning). For this exercise, gain is considered to be 1.0. (A) If the transmitter is a flow transmitter whose behaviour can be described by a dead time of 0.2 min. and an exponential lag of 0.5 min. in terms of the overall dead time and overall first order lag how can the system behaviour be approximated ? Overall dead time = Overall time constant = (B) If the transmitter is a temperature transmitter with a temperature sensor in a protecting well whose behaviour can be described by a dead time of 0.7 min. and an exponential lag of 15 min. how can the overall system behaviour be approximated now? Overall dead time = Overall time constant =

1988

---

How many interlocks at turbine? Plz explain briefly

2005

---

What is zero elevation and zero suppression?

2236

---